| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| SRS-0824A | SURFACE REFERENCE ST | 3 | |
| SRS-0824S | SURFACE REFERENCE ST | 3 |
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| (CALIB) SRS-0824A | SRS, SURFACE REFERENCE STANDARD (CALIBRATION) | 1 | |
| 126 | SURFACE CRACK REFERENCE STANDARD | 7 | |
| 29A029 | SURFACE REFERENCE STANDARD | 5 | |
| 6AL-6V-2SN-Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" +/-.001 DEEP, (MAX WIDTH .005"), 6AL-6V-2SNTi | 1 | |
| 99A51107300000 | AIRBUS A330 REFERENCE STANDARD FOR SUBSURFACE CRACKS IN AL-ALLOY 51-10-16-991-011-A. PART 6, PAGE 615 FIGURE 610PROCEDURE B. Includes Test Report and Certificate of Conformance... | 5 | |
| 99D57103014000 | AIRBUS REFERENCE STANDARD A318 - A321 57-11-85-PB 4. Surface Annodizing, Primer+ Top Coat. Includes Test Report and Certificate of Conformance. | 5 | |
| AF-5037 | STAINLESS STEEL SURFACE PROBE, SHIELDED, 90° DEGREES, .125"Ø SHAFT, BENT 30° 1.0" FROM THE TIP, .250" DROP, 50-500KHz. TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. Reference:.... RMTF902-25-60B | 1 | |
| AF-5144 | Rigid Surface Probe Absolute Shielded, 200KHz Center Frequency, .187"Ø Tip, 90°, .250" DROP, 15° Degree Crank, 4.5" long with Microdot Connector. Includes Test Report and Certificate of Conformance. Reference: 610-094-111 | 1 | |
| AF-5144/TF | Rigid Surface Probe Absolute Shielded, 200KHz Center Frequency, .187"Ø Tip, 90°, .250" DROP, 15° Degree Crank, 4.5" long with Triax Fischer Connector. Includes Test Report and Certificate of Conformance. Reference: 610-094-111 | 1 | |
| AF-5224/2MHZ | SURFACE PROBE .070"Ø TUBING ABS SHIELDED 90°, .300" DROP, 6.0" LONG, , 1-3MHz, SUPPLIED WITH A TRIAX FISCHER CONNECTOR Includes Test Report and Certificate of Conformance. Reference: MD-11 Section 2-2 figure 2.4 PG.3 | 1 | |
| AF-5225/500K | RIGID SURFACE PROBE .062"Ø TUBING ABS SHIELDED 90°, 60° Joggle.020" DROP, 6.0" LONG, , 500KHz, SUPPLIED WITH A TRIAX FISCHER CONNECTOR Includes Test Report and Certificate of Conformance. Reference: MD-11 Section 2-2 figure 2.4 PG.4 | 1 | |
| AF-5226 | CUSTOM MICRO INDEXING EDDY CURRENT SURFACE PROBE ASSEMBLY WITH 3 PROBE TIPS: 100KHz-300KHz, 500KHz, 1-3MHz. INCLUDES Includes Test Report and Certificate of Conformance. Reference: MD-11 Section 2-2 figure 2.7 PG.5. | 1 | |
| AF-5278/TF | HIGH FREQUENCY SURFACE PROBE, Twin Coil Differential 50-500KHZ. 4.0" Long 0.375" Diameter with Triax Fischer connector. For use with Boeing Reference Standard 497 767 Part 6 53-00-04. IncludesTest Report and Certificate of conformance. | 1 | |
| AF-NEC-6112-1/Ti | Custom multi-hole reference standard Material: 6AL-4v Titanium. Hole sizes: 1/8", 5/32", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8",11/16" and 3/4". Countersink holes opposite side. Thru hole EDM notches in each hole .005" +/-.001". 3 Surface... | 1 | |
| AFNDT-0212-1 | EDDY CURRENT SURFACE REFERENCE BLOCK. 2 EDM NOTCHES ( .012"D, .020"D, x .005" W +/- .001"), INCONEL 718. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000/4340 | 12 HOLE REFERENCE STANDARD 4340 STEEL WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000/SA | 12 HOLE REFERENCE STANDARD ALUMINUM WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000SA-1 | 12 HOLE REFERENCE STANDARD ALUMINUM WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000SS | 12 HOLE REFERENCE STANDARD STAINLESS STEEL WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000TI | 12 HOLE REFERENCE STANDARD 6AL4V WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1025AL | Multi-Hole reference standard. Material: 7075-T6 Aluminum. 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" .020" x .020" x .005" Wide ± .002" Through EDM Notches in each hole. Standard also includes 3 surface EDM n | 1 | |
| AFNDT-1025TI | Multi-Hole reference standard. Material: 6Al-4v Titanium. 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" .020" x .020" x .005" Wide ± .002" Through EDM Notches in each hole. Standard also includes 3 surface EDM no | 1 | |
| AFNDT-1080/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES 0.5mm, 1.0mm, 2.0mm, 3.00mm, 4.0mm, 5.0mm (.004"W +/- .002, MAX.006), 4340 STEEL 1.0"W x 7.0"L. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2003-2S | 12 HOLE REFERENCE STANDARD 1018 STEEL HOLE SIZES: .187", .250" ,.312", .375", .437", .500", .562", .625", .687", .750", AND 1.0" ( .030X.030 CORNER NOTCH and 3 SURFACE NOTCHES .010", .020", .040" DEEP x .750" LONG.) 304 STAINLESS STEEL. Includes Test Repo | 1 | |
| AFNDT-2005A | 12 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .030" x .030" CORNER NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and Certificate o | 1 | |
| AFNDT-2005TI | 12 HOLE REFERENCE STANDARD 6AL-4v TITANIUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .030" x .030" CORNER NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and Certificate of | 1 | |
| AFNDT-2006/300M | 12 HOLE REFERENCE STANDARD 300M STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEEP .005" ... | 1 | |
| AFNDT-2006A | 12 HOLE REFERENCE STANDARD 7075-T6 aluminum. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.004" ±.002" WIDE CORNER EDM NOTCH in EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020",... | 1 | |
| AFNDT-2006S | 12 HOLE REFERENCE STANDARD 4130 or 4340 STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEE... | 1 | |
| AFNDT-2006SS | 12 HOLE REFERENCE STANDARD 304 304 STAINLESS STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040... | 1 | |
| AFNDT-2006TI | 12 HOLE REFERENCE STANDARD 6AL-4V.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEEP .005" WIDE... | 1 | |
| AFNDT-2014Ti | 12 HOLE REFERENCE STANDARD IN 6AL-4v Ti; HOLE SIZES: (3/16, 7/32 ,1/4, 9/32, 5/16,11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4), .010", .020", .030", and .040" SURFACE NOTCHES. .050"x.050" CORNER EDM NOTCH and .030"x.030" CORNEREDM NOTCH, .050"Lx.030"D MID-... | 1 | |
| AFNDT-2030/13-8 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/13-8PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH MO STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-7PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-7PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2014-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2014-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2014-T651 | DDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2014-T651 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/300M | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: 300M STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/301 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), CRES 301 1/2 HARD(MIL-S-5059) 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304L | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304L STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/316SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 316 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4130 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4130 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/6061-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002), 6061-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-2030/7075-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/7075-T7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/718 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 718 INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/I600 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 600 SERIES INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/MAG | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| AFNDT-2030/MAR | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002). MATERIAL: 250 MARAGING STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/N200 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: NICKEL 200. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX .006"), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and COC | 1 | |
| AFNDT-2030CS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), 4130 or 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030INC | EDDY CURRENT SURFACE REFERENCE BLOCK, EDM NOTCHES ( .008", .020", .040" x .004" W +/- .002"), INCONEL 718. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2035 | 6 Hole reference standard (Aluminum 7075-T6 with certifications). Hole Sizes: 1.0", 1.125", 1.250" ,1.500", 1.625", 1.750", ( .030 x .030 x .006 +/- .001) Corner EDM Notches and .010, .020, .040 Surface notches).. Includes Test Report and Certificate | 1 | |
| AFNDT-2063 | 10 HOLE REFERENCE STANDARD 6AL-4V TITANIUM, HOLE SIZES: 1/8, 3/16 , 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4, .030X.030 CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .75L X.010,.020,.040 DEEP. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2063S | 10 HOLE REFERENCE STANDARD 4340 STEEL, HOLE SIZES: 1/8, 3/16 , 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4, .030X.030 CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .75L X.010,.020,.040 DEEP. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2064/AL | SAFRAN MESSIER-BUGATTI-DOWTY ET SURFACE REFERENCE STANDARD 32-09-01 FIGURE 67,GRAPHIC-32-09-01-041-008-A01. MATERIAL: 2024-T351 ALUMINUM. Includes Test Report and Certificate of conformance. | 1 | |
| AFNDT-2066/TI | 12 HOLE REFERENCE STANDARD 6AL-4V TITANIUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .001" WIDE THRU NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and C | 1 | |
| AFNDT-2066A | 12 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .001" WIDE THRU NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and | 1 | |
| AFNDT-2074 | CUSTOM SURFACEREFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .007" MAX WIDTH. MATERIAL: 7075-T6 ALUMINUM. SIZE: 4.0 x 1.5 x .25". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-2083 | 10 HOLE REFERENCE STANDARD 2024-T3, HOLE SIZES, 1/8,5/32, 3/16 , 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, .030X.030 CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .75L X.010,.020,.040 DEEP. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/6AL4V | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2114AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.006W +/- .001). BLOCK SIZE:3.156 "L x 1.375"W x .312"H. MATERIAL: 2024-T3 ALUMINUM.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2123AL | 12 HOLE REFERENCE STANDARD 7075-T6, 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", .005" +/-.001" THROUGH NOTCH ON EACH HOLE and A .030" x .030" x .005+/- .001" CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .008", .020"... | 1 | |
| AFNDT-2123S | 12 HOLE REFERENCE STANDARD 4340 STEEL, 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", .005" +/-.001" THROUGH NOTCH ON EACH HOLE and A .030" x .030" x .005+/- .001" CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .008", .0... | 1 | |
| AFNDT-2123TI | 12 HOLE REFERENCE STANDARD 6AL-4v TITANIUM, 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", .005" +/-.001" THROUGH NOTCH ON EACH HOLE and A .030" x .030" x .005+/- .001" CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .008... | 1 | |
| AFNDT-2136 | 12 HOLE REFERENCE STANDARD 6061-T6. HOLE SIZES: 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4". .030" x .030" x .005" +/- .001" W CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .008", .020", .040" . .005" +/-.001". Includ | 1 | |
| AFNDT-2151AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.005"W + .001"), MATERIAL: 5086 H32 ALUMINUM. (29.0% IACS. SIZE: 80mm(3.15") L +5mm(.197") x 30mm(1.18") W +5mm(.197") x 8mm(.315") THICK +3mm(.118"). Includes Mill Certifica... | 1 | |
| AFNDT-3007 | SURFACE NOTCH REFERENCE STANDARD 15-5 PH STEEL. EDM NOTCH SIZE: FULL WIDTH OF PART x .20mm(.008") WIDE x .50mm(.020") DEEP +/- .05mm(.002"). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3015 | EMBRAER 170/190 SERIES EDDY CURRENT SURFACE REFERENCE STANDARD 50-00-00 PT 1 PAGE 4, Aluminum(7075-T6) 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3024AL | 12 HOLE REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X .030" X .005" +/- .001" WIDE CORNER EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG . | 1 | |
| AFNDT-3026AL | EDDY CURRENT SURFACE REFERENCE STANDARD Leonardo Helicopters SB No. 109EP-158. MATERIAL: 7475-T7 ALUMINUM. SIZE: 1.0" x 3.0" x .25" EDM SLOT (0.5mm DEEP) x (0.05-0.25mm WIDE) +/-.03mm. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3027AL | MHS style Multi-Hole reference standard (Aluminum 7075-T6 with certifications). 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16" ( .030 x .030 x .006 +/- .001) Corner Notches and .010, .020, .040 Surface notch... | 1 | |
| AFNDT-3035SS | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM NOTCHES: .005", .010", .020", .060" (.005"W +/- .002, MAX.007" WIDE). MATERIAL: 301 1/2 HARD STAINLESS STEEL(MIL-S-5059) 1.0"W x 4.0"L x .125", NOTE: .750" DISTANCE BETWEEN EACH NOTCH. Includes Test Repor... | 1 | |
| AFNDT-3055 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4330 STE... | 1 | |
| AFNDT-3058/INC | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .5mm, 1.0mm, 2.0mm x (.006"Wide +/- .001). MATERIAL: 718 Inconel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3058SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES: 0.5mm, 1.0mm, 2.0mm x (.005"Wide + .000/-.002). MATERIAL: 304 Stainless Steel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3061AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3120AL | 11 hole Reference Standard 7075-T6 Aluminum. Contains 10 hole sizes; 7/64, 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4 and 1.0 inch diameters.( .030X.030 Corner EDM Notch and 3 Surface EDM Notches at .010", .020", .040" DEEP x .750" LONG.) Includes T... | 1 | |
| AFNDT-3121S | 10 hole Reference Standard 4340 or 4130 Carbon Steel. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .030" x .030" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", ... | 1 | |
| AFNDT-3122T-0 | 10 hole Reference Standard 6AL-4v Titanium. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .030" x .030" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", .040" Dee... | 1 | |
| AFNDT-3122T-4 | 10 hole Reference Standard 6AL-4v Titanium. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .050" x .050" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", .040" Dee... | 1 | |
| AFNDT-3145S | 12 HOLE REFERENCE STANDARD 4340 STEEL, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", .020" x .005" +/-.001" THROUGH NOTCH ON EACH HOLE, A .030" x .030" x .005+/- .001" CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .01... | 1 | |
| AFNDT-3151AL | 15 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM, HOLE SIZES: 1/8, 5/32, 3/16, 7/32 ,1/4, 9/32, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4,,7/8,1.0" .030" x .030" CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .750"L x .010",.020",.040" DEEP. Includes Test Report and | 1 | |
| AFNDT-3151CS | 15 HOLE REFERENCE STANDARD 4130 OR 4340 CARBON STEEL, HOLE SIZES: 1/8, 5/32, 3/16, 7/32 ,1/4, 9/32, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4,,7/8,1.0" .030" x .030" CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .750"L x .010",.020",.040" DEEP. Includes Test Re | 1 | |
| AFNDT-3151SS | 15 HOLE REFERENCE STANDARD 304 STAINLESS STEEL, HOLE SIZES: 1/8, 5/32, 3/16, 7/32 ,1/4, 9/32, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4,,7/8,1.0" .030" x .030" CORNER NOTCH .005+/-.001, 3 SURFACE NOTCHES .750"L x .010",.020",.040" DEEP. Includes Test Report a | 1 | |
| AFNDT-3198TI | 10 HOLE REFERENCE STANDARD 6AL-4V Titanium.Hole Sizes: (3/16", 7/32" ,1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005" +/-.002" WIDE & .020" X. 020" x.005" +/-.002" WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .500... | 1 | |
| AFNDT-3201/321SS | EDDY CURRENT SURFACE REFERENCE STANDARD, 321SS 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3210 | SURFACE REFERENCE STANDARD, ONE EDM NOTCH .030" Deep x .040" wide x .060 long ( +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 2.0"L x 2.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3224TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020", .040", .060" (.005"W +/- .002, MAX .007"). MATERIAL: 6AL-4v TITANIUM@2.2IACS. SIZE: 1.0"W x 6.0"L x .500". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3225AL | 12 HOLE REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010"... | 1 | |
| AFNDT-3225I | 12 HOLE REFERENCE STANDARD. MATERIAL: 718 INCONEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020... | 1 | |
| AFNDT-3225S | 12 HOLE REFERENCE STANDARD. MATERIAL: 4130 or 4340 CRES STEEL. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LON... | 1 | |
| AFNDT-3225TI | 12 HOLE REFERENCE STANDARD. MATERIAL: 6AL-4V TITANIUM.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", ... | 1 | |
| AFNDT-3239AL | 3 HOLE REFERENCE STANDARD 2024-T3 ALUMINUM. HOLE SIZES: 1/4", 5/16", 3/8" TOTAL OF 3 EDM CORNER NOTCHES .030" x .030". 3 EDM SURFACE NOTCHES 0.008", 0.020", 0.040". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3251AL | 12 HOLE REFERENCE STANDARD 2024-T3 ALUMINUM. HOLE SIZES: 1/8", 3/16" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8",11/16", 3/4", 13/16" .030" x .030" CORNER NOTCH and .020" x .020" CORNER NOTCH IN EACH HOLE. Tolerance: .005" +/-.001", 4 SURFACE EDM NOTCH | 1 | |
| AFNDT-3251TI | 12 HOLE REFERENCE STANDARD 6AL-4V TITANIUM. HOLE SIZES: 1/8", 3/16" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8",11/16", 3/4", 13/16" .030" x .030" CORNER NOTCH and .020" x .020" CORNER NOTCH IN EACH HOLE. Tolerance: .005" +/-.001", 4 SURFACE EDM NOTCHE | 1 | |
| AFNDT-3279/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3279/Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3280 | Surface reference standard, 4340 Steel, with EDM notch depths of 0.5mm", 1.0" and 2.0mm +/-1.3mm, Notch Width: .18mm Max. Depth: +/- .03mm. Reference standard overall dImensions 25.4mm X 101.6mm X 6.4mm). Includeds .020" thick shim and Key Ring. Supplie | 1 | |
| AFNDT-3284SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm), .050"(1.27mm) (.004"W +/- .001), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. REFERENCE P/N:29A049 | 1 | |
| AFNDT-3285/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-4PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/17-7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-7PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/MAG | EDDY CURRENT METRIC SURFACE REFERENCE STANDARD. EDM NOTCH SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: MAGNESIUM ZK60A-T5 PER ASTM-B107. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3312AL | 12 HOLE REFERENCE STANDARD, 7075-T6 Aluminum. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010" .020", .040" Tolerance: . | 1 | |
| AFNDT-3314SS | 12 HOLE REFERENCE STANDARD, 304 STAINLESS STEEL. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010", .020", .050" Tolera... | 1 | |
| AFNDT-3314TI | 12 HOLE REFERENCE STANDARD, 6AL-4V TITANIUM. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010", .020", .050" Tolerance: . | 1 | |
| AFNDT-3315AL | EDDY CURRENT SURFACE REFERENCE STANDARD, 4 EDM NOTCHES .005", .010", .020" and .050" x (.004"W +/- .002). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3319SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .020"(0.5mm), .040"(1.0mm), .079"(2.0mm) (.005"W +/- .002), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3332CS | 20 HOLE REFERENCE STANDARD 4340 STEEL. HOLE SIZES: 1/8, 5/32, 11/64, 3/16, 13/64, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 17/32, 9/16, 5/8, 11/16, 3/4. TOTAL OF 20 CORNER EDM NOTCHES .030 x .030 x .005 +/-.001. TOTAL OF 20 SURFACE TO | 1 | |
| AFNDT-3338/17-4 | Surface reference standard, 17-4PH Steel, with EDM notch depths of 0.005", 0.010" and 0.020" inches +/-.001 (0.127mm, 0.254mm and .508mm), Notch Width: .004" +/-.001" Wide EDM notches, .005" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| AFNDT-3347CS | EDDY CURRENT WELD SURFACE REFERENCE STANDARD. EDM NOTCHES: 0.5mm, 1.0mm, 2.0mm (.1mm (.004") WIDE ± .05mm( .002") MAX WIDTH .152mm (.006"). MATERIAL: 4340 CARBON STEEL. SIZE: 1.0"W x 4.0"L Includeds 4 piece .020" thick shim and Key Ring set. Includes Tes | 1 | |
| AFNDT-3353/2024T3 | Custom 12 Hole Reference Standard. Contains hole sizes; 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8 and 3/4 inch diameters. ( .030 x .030) Corner EDM Notches and .020" mid-wall EDM Notches, 3 Surface EDM Notches .008", .020", .040" Deep | 1 | |
| AFNDT-3353/I625 | Custom 12 Hole Reference Standard. Contains hole sizes; 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8 and 3/4 inch diameters. ( .030 x .030) Corner EDM Notches and .020" mid-wall EDM Notches, 3 Surface EDM Notches .008", .020", .040" Deep | 1 | |
| AFNDT-3357/2024T4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .001), 2024-T4 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-3370/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(.76mm) (.004"W +/- .002), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3396CS | SURFACE NOTCH REFERENCE STANDARD 4130 or 4340 CARBON STEEL. EDM NOTCH SIZE: FULL WIDTH OF PART x .51mm(.020") DEEP +/- .05mm(.002"). BLOCK SIZE: 1.0" WIDE x 3.0" LONG. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3399S | 12 HOLE REFERENCE STANDARD 4340 STEEL.Hole Sizes: 6.35mm, 5.54mm, 4.75mm, 3.96mm, 3.18mm, 2.36mm. (1/4", 7/32", 3/16", 5/32", 1/8", 3/32"), 0.5mm x 0.5mm x 0.15mm (.0197" X .0197" x.0059")WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES 0.2mm, | 1 | |
| AFNDT-3440/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3440/6AL-4V | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: 6AL-4V Titanium. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3457 | EDDY CURRENT SURFACE REFERENCE STANDARD. Cadmium plated on one side to AMS-QQ-P-416-f Type 1, Class 2. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .008", .020", .040". NOTCH WIDTH: (.004"W +/- .002). MATERIAL: 4340 STEEL. SIZE: 1. | 1 | |
| AFNDT-3470/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCH .020"(0.5mm), (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 3.0"L x .25".Includes certification Report Traceable to NIST and Certificate of Conformance(COC). | 1 | |
| AFNDT-3499 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 4 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .005", .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4... | 1 | |
| AFNDT-3500/MAG | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020", 0.030 and 0.040" inches (0.2mm, 0.51mm, 0.76mm and 1.02mm). Reference standard overall dImensions 1 X 5 X 0.25 inches (2.54cm X 12.7cm X 6.35mm). EDM notches .007" W MAX Inclu | 1 | |
| AFNDT-3522AL | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 7075-T6 ALUMINUM. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522SS | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 304 STAINLESS STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522ST | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 4340 STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3534/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.5mm), .030"(.762mm) (.004"W +/- .002), 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3546AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHE SIZES: .005"(.127mm) , .020"(0.5mm), .050"(1.27mm) (.005"W +/- .001). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3559AL-3 | 15 HOLE REFERENCE STANDARD, Material: 7075-T6 Aluminum. Hole Sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1.0. A Total 15 Mid-bore notch @ 0.030" deep x 0.004" wide x 0.060" long in each hole. 3 Surface EDM No... | 1 | |
| AFNDT-CRJ200/CRS | SURFACE REFERENCE STANDARD, ALUMINUM, .005W x .008", .020", .040" EDM NOTCH DEPTHS . MATERIAL 2024-T3 AL...CRJ200 PART1 51-20-06 PG.9 | 1 | |
| AFS-0584 | CUSTOM BOEING 747 TRANSDUCER 35° IN STEEL WITH A 2.220" RADIUS FINGERTIP RADIUS GRIP ON TOP SURFACE, USED WITH NDT4279. Includes Test Report and Certificate of Conformance. Reference: 747 Part 4 57-40-08 | 1 | |
| AFS-0591 | CUSTOM BOEING 747 TRANSDUCER 33° IN STEEL WITH A 2.220" RADIUS FINGERTIP RADIUS GRIP ON TOP SURFACE, USED WITH NDT4280. Includes Test Report and Certificate of Conformance. Reference: 747 Part 4 57-40-08 | 1 | |
| AFS-766/767-4 | CUSTOM 5MHz ANGLE BEAM TRANSDUCER .25" x .25" ELEMENT. USED WITH NDT766 Outboard Flange of the T-Chord/Lower Surface. Includes Test Report and Certificate of Conformance.REFERENCE: 777 PART 4 57-10-02 | 1 | |
| AL29-32 | CALIBRATION REFERENCE STANDARD, BLOCK, 2024-T3 ALUMINUM ALLOY, CONDUCTIVITY BETWEEN 29% AND 32% IACS, CONTAINS 0.008 IN. (0.20 MM), 0.020 IN. (0.51 MM), AND 0.040 IN. (1.02 MM) DEEP SURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES, (MHIRJ OR EQUIVALENT) | 6 | |
| AL35-45 | BOMBARDIER SURFACE REFERENCE STANDARD - 7075-T7ALUMINUM. FULL WIDTH EDM NOTCHES .008", .020", .040" (.005"W +/- .002, MAX.006) BLOCK SIZE: 3.75"L x 1.50"W x 0.25"H | 8 | |
| ARS-0812S | Surface reference standard, 17-4PH Steel, with EDM notch depths of 0.008", 0.010" and 0.020" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inc | 1 | |
| ARS-0824-7050 | Surface reference standard, 7050-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824-7050T74 | Surface reference standard, 7050-T74 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824-7075T6 | Surface reference standard, 7075-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824-7075T7 | Surface reference standard, 7075-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824-7075T73 | Surface reference standard, 7075-T73 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/2024-T3 | Surface reference standard, 2024-T3 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824/2024-T6 | Surface reference standard, 2024-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/2024T6 | Surface reference standard, 2024-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/4330 | Surface reference standard, 4330 Steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inches | 1 | |
| ARS-0824/6061T6 | Surface reference standard, 6061-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824/7475-T7 | Surface reference standard, 7475-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824A | Surface reference standard, 7075-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824I | Surface reference standard, Inconel 718, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824M | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824S | Surface reference standard, 4340 Steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inc... | 1 | |
| ARS-0824SS | Surface reference standard, 304 Stainless steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM NOTCHES .005" W +/-.001" | 1 | |
| ARS-0824SS/316 | Surface reference standard, 316 Stainless steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM NOTCHES .005" W +/-.001" | 1 | |
| ARS-0824T | Surface reference standard, 6AL-4v Titanium, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.2... | 1 | |
| ARS-123/TI | EDDY CURRENT SURFACE REFERENCE STANDARD. MATERIAL: TI-6AL-6V-2SN. SIZE: 2.0" LONG x 1.0" WIDE. EDM NOTCH .040" DEEP +/- .002" x .005" WIDE +/- .001". Includes Test Report and Certificate of Conformance. | 1 | |
| ARS-1S | Surface reference standard, 4340 or 4130 steel, with EDM notch depth of 0.010" x .005" wide Reference standard overall dImensions 1.0" X 3.0" X 0.25" inches .007" W MAX. Includes Certification traceable to NIST. | 1 | |
| BHS6061-T6/C2 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | 1 | |
| CFM56 9970-958-579 | EDDY CURRENT SURFACE REFERENCE BLOCK. 2 EDM NOTCHES .012" Deep x .004" Wide and .020" Deep x .004" Wide. Tolerance on Width (.004" W +/- .002"), Material: Inconel 600 Series. Reference: CFM56-5B S/B 72-0620 PAGE 14. Includes Test Report and Certificate | 2 | |
| DAC GSET AL.01-MV | 7075-T6 Aluminum Multi-purpose Reference Standard, Modified Version, Surface notches are only .125"long from edge of standard | 1 | |
| DAC GSET AL.01-N1-N2 | General Surface Aluminum HFET Reference Standard MD-11 section 2-1 page 1 figure 1.1 | 1 | |
| DAC GSET TI.01-MV | 6AL-4V Titanium Multi-purpose Reference Standard, Modified Version, Surface notches are only .125"long from edge of standard | 1 | |
| DAC GSET Ti.01-N1-N2 | General Surface Titanium HFET Reference Standard MD-11 section 2-1 page 1 figure 1.2 | 1 | |
| ET.28 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | 1 | |
| EXSH670-31001-1 | CALIBRATION REFERENCE STANDARD, STGR15R BUTT JOINT, CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES, (MHIRJ) | 1 | |
| EXSH670-31001−1 | CALIBRATION REFERENCE STANDARD STGR15R BUTT JOINT CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES (BOMBARDIER INC.) | 1 | |
| EXSH670-31002-1 | CALIBRATION REFERENCE STANDARD STGR1L AND STGR20L BUTT JOINTS CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES (BOMBARDIER INC.) | 1 | |
| EXSH670−31001−1 | Calibration reference standard STGR15R butt joint contains surface and subsurface electrical discharge machined notches (Bombardier Inc.) | 1 | |
| EXSH670−31002−1 | Calibration reference standard STGR1L and STGR20L butt joints contains surface and subsurface electrical discharge machined notches (Bombardier Inc.) | 1 | |
| EXSH670−31014−1 | Calibration reference standard pressure bulkhead machined frames FS693.00 and FS847.00 contains subsurface electrical discharge machined notches. (Bombardier Inc.) | 1 | |
| EXSH690-31003−11 | CALIBRATION REFERENCE STANDARD EMERGENCY EXIT DOOR SURROUND STRUCTURE CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES (BOMBARDIER INC.) | 1 | |
| EXSH690-31023-1 | CALIBRATION REFERENCE STANDARD, CIRCUMFERENTIAL SKIN JOINT STGR7 TEST PIECE, CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES (MHIRJ) | 1 | |
| EXSH690-31023−1 | CALIBRATION REFERENCE STANDARD CIRCUMFERENTIAL SKIN JOINT STGR7 TEST PIECE CONTAINS SURFACE AND SUBSURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES (BOMBARDIER INC.) | 1 | |
| EXSH690−31003−11 | Calibration reference standard emergency exit door surround structure contains surface and subsurface electrical discharge machined notches (Bombardier Inc.) | 1 | |
| EXSH690−31023−1 | Calibration reference standard circumferential skin joint STGR7 test piece contains surface and subsurface electrical discharge machined notches (Bombardier Inc.) | 1 | |
| MD11-05b | MD11 SUBSURFACE ALUMINUM ETLF REFERENCE STANDARD FIG 1.10 (Sheets 1-5) Section 2-1 Pages 1-5. Includes Test Report and Certificate of Conformance. | 1 | |
| MD11-05c | MD11 SUBSURFACE ALUMINUM ETLF REFERENCE STANDARD FIG 1.11 (Sheets 1-5) Section 2-1 Pages 1-5. Includes Test Report and Certificate of Conformance. | 1 | |
| NDETECH-7515 | CALIBRATION BLOCK STAINLESS STEEL SURFACE REFERENCE STANDARD 304 STAINLESS STEEL. | 1 | |
| NDT3305A | REFERENCE STANDARD: SUBSURFACE | 2 | |
| NDT3305B | REFERENCE STANDARD: SUBSURFACE | 3 | |
| RM120-C30-304-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 304 STAINLESS STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RM120-C30-4340-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 4130 STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RM120-C30-7075T6-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 7075-T6 ALUMINUM, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RM200-C20T20-T6AL4V | 20 Hole Reference Standard, 1/8" Thru 3/4", w/20" Cornor Notch, w/ .20" Thru Notch, T6AL4V, Plus .008", .020" & .040" surface notches | 1 | |
| RM200-T40-T6AL4V | CALIBRATION REFERENCE STANDARD, TITANIUM ALLOY, CONDUCTIVITY 1.1 % IACS, CONTAINS 0.010 IN. (0.25 MM), 0.020 IN. (0.51 MM), AND 0.040 IN. (1.02 MM) DEEP SURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES, AND VARIOUS SIZE HOLES WITH 0.040-IN (1.02 MM) EDM NOTC | 1 | |
| RM290-C30-7075T6 | Reference Standard, 29 Holes 1/8" thru 1" in 1/32" increments with .030" corner notch plus 3 surface notch | 1 | |
| RM290-T20-2014T6 | multi-hole reference standard 29 holes 1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 17/32, 9/16, 19/32, 5/8, 31/32, 11/16, 23/32, 3/4, 25/32, 13/16, 27/32, 7/8, 29/32 15/16, 31/32 0.020 deep through notch 3 surface flaws... | 1 | |
| RS-0123-2024T3 | Surface Reference Standard .10" .020" .030" long 2024T3 | 1 | |
| RS-0123-7075T6 | Surface Reference Standard .010" .020" .030" long 7075T6 | 1 | |
| RS0212-1 | Reference Standard, Inconel 718, Surface Notches, .012, .020" Depth | 1 | |
| RS0824 | SRS, SURFACE REFERENCE STANDARD | 1 | |
| RS0824-.060-2024T3 | Surface Reference Standard, .008", .020", .040" x .060" Long, 2024T3 Aluminum | 1 | |
| RS0824-.060-7075T6 | Surface Reference Standard, .008", .020", .040" x .060" Long, 7075-T Aluminum | 1 | |
| RS0824-2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 4.0"L X 1.0"W X .25". INCLUDES TEST REPORT AND CERTIFICATE OF CONFORMANCE. | 2 | |
| RS0824-316 | SURFACE REFERENCE STANDARD WITH CERTIFICATE TRACEABLE TO NIST. STAINLESS STEEL (316) WITH EDM NOTCH DEPTHS OF 0.008, 0.020 AND 0.040 INCHES, BLOCK OVERALL DIMENSIONS 1 X 4 0.25 INCHES. | 1 | |
| RS0824-4340-VMS3RS-062 | Reference Standards are 3” Long x 2” Wide x ¼” Thick, 3 Surface EDM notches: 0.008” deep x 0.062” long, 0.020” deep x 0.062” long and 0.040” deep x 0.062” long | 1 | |
| SB09540030-5 | DC9 SURFACE REFERENCE REFERENCE STANDARD DC9-54-030. MATERIAL: 17-7 PH STAINLESS STEEL. EDM NOTCH: 0.002"-0.010" WIDE x 0.030" DEEP. | 1 | |
| SK601R-30008A | CALIBRATION REFERENCE STANDARD (CRS), MULTIPLE LAYERED FASTENED ASSEMBLY, EQUIVALENT IN MATERIAL AND THICKNESS AS THE INSPECTION AREA CONTAINING SUBSURFACE ELECTRICAL DISCHARGE MACHINED (EDM) NOTCHES (MHIRJ). | 6 | |
| SPT- RM200-C20T20-T6AL4V | 20 Hole Reference Standard, 1/8" Thru 3/4", w/20" Cornor Notch, w/ .20" Thru Notch, T6AL4V, Plus .008", .020" & .040" surface notches | 1 | |
| SRS-0824A | SRS, SURFACE REFERENCE STANDARD | 3 | |
| SRS-0824A-7075T6 | SURFACE REFERENCE STANDARD (7075-T6) | 1 | |
| SRS-0824M | REFERENCE STANDARD FOR SURFACE INSPECTION | 1 | |
| SRS-0824M- AZ31B | SURFACE REFERENCE STANDARD, MAGNESIUM AZ91E, WITH EDM NOTCH DEPTHS OF 0.008", 0.020" AND 0.040" INCH | 1 | |
| SRS-0824S | REFERENCE STANDARD FOR SURFACE INSPECTION | 3 | |
| SRS-0824S-4130 | SURFACE REFERENCE STANDARD WITH CERTIFICATE, STEEL (4130) WITH EDM NOTCH DEPTHS OF 0.008, 0.020 AND 0.040 INCHES. BLOCK OVERALL DIMENSIONS 1 X 4 X 0.25 INCHES . | 1 | |
| SRS-0824SS | REFERENCE STANDARD FOR SURFACE INSPECTION | 1 | |
| SRS-0824SS-316 | SURFACE REFERENCE STANDARD WITH CERTIFICATE TRACEABLE TO NIST. STAINLESS STEEL (316) WITH EDM NOTCH DEPTHS OF 0.008, | 1 | |
| SRS-0824T | REFERENCE STANDARD FOR SURFACE INSPECTION | 3 | |
| ST4130 | BOMBARDIER / CANADAIR EDDY CURRENT SURFACE REFERENCE STANDARD PART 6 55-20-001, NOTCHES .008", .020", .040" (.005" Wide +000 / - .002 and +/- .001" Depth), MATERIAL: 4130 STEEL. Includes certification Report and Certificate of Conformance(COC)... | 1 | |
| ST895A-3 | PROBE - RESISTIVITY MEASUREMENT, SURFACE NOTE: OPTIONAL TOOL / LOW USE TOOL - ONLY USE FOR OPTIONAL ST895A-3 TEST METHOD WHICH IS NOT CURRENTLY USED IN 737NG AMM -51-21- 71 - SEE REFERENCED BAC5639 PSD 6-14, PAGES 11 - 13 | 6 | |
| STANDARD-B | 2/64" FLAT BOTTOM HOLE EQUIVALENT SURFACE NOTCH STANDARD (*ABOVE DESCRIPTION MUST BE ENGRAVED ON THE REFERENCE STANDARD) ..DRAWING "B" (PS21211.3 FOR F/A-18 OUTER WING FORWARD SPAR) MATERIAL=7075-T6 | 1 | |
| TEK-9087L | 5 MHZ SURFACEWAVE TRANSDUCER, REFERENCE STANDARD NDT3310, LEFT SOUND DIRECTION | 1 | |
| TEK-9087R | 5 MHZ SURFACEWAVE TRANSDUCER, REFERENCE STANDARD NDT3310, RIGHT SOUND DIRECTION | 1 | |
| VM89A | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 7075-T6 ALUMINUM, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| VM89S | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 4130 STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| VM89SS | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 304 STAINLESS STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 |
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
