| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| NDT689-P | REFERENCE STANDARD W | 3 |
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| (CALIB) HORIZONTAL STAB SLINGS | CALIBRATE AND RE-CERTIFY THIS TOOL (HORIZONTAL STAB SLINGS) IN ACCORDANCE WITH BOEING DWG C55007 REV. D (OR LATER) AND LOLER 1998 (OR LATER). TEST/CALIBRATION CERTIFICATE MUST REFERENCE MAINTENANCE DATA (MANUAL/STANDARD) AND REVISION USED. ADDITIONAL REFE | 1 | |
| 1/N-02-384 | Nomad Series N22 & N24 Reference Standard. for the inspection of Wing Strut Upper Fittings, Figure 27 Page 51. Includes Test Report and Certificate of Conformance. | 1 | |
| 10-0109-00 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601, INCONEL 718, 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 2 | |
| 10RS.15c | DC-10 SID REFERENCE STANDARD DETAILS -7, -9 & -11, -503 ASSWMBLY PAGE 1-6. MATERIAL: 7075-T6 ALUMNIUM. Includes Certification Report and COC. | 1 | |
| 10RS.51-MLG-FTG-FF | Reference Standard, DC10 MLG plus 4 notches, Includes wood model | 1 | |
| 1409-00-2 | KIT REFERENCE STANDARD NDI- TORQUE BOX. NDI WING ASSY. | 11 | |
| 145-44130-401 | KIT REFERENCE STANDARD NDI- TORQUE BOX. NDI WING ASSY. | 3 | |
| 145T09065-401 | REFERENCE STANDARD FOR FASTENER HOLE INSPECTION WITH PN 145T09065-401AND EMBRAER GSE NUMBER 606. | 1 | |
| 171-00844-601 16E1 | REFERENCE STANDARD - LWR AFT ATG ANTENNA ( SPEC. ALUMINIUM 7475 T7351). | 1 | |
| 17P9M2007 | Douglas Reference Standard Assembly For the Ultrasonic Calibration of Upper Wing Skin to common Stringer, Figure24-4 sheets 253. Material: 7075 Aluminum. Includes Test Report Traceable to NIST and Certificate of Conformance. | 1 | |
| 186ABCDEF | BOEING CUSTOM COMBINATION REFERENCE STANDARD 777 PT 6 51-00-02 Figures 1&2, Pages 6-7, HOLE SIZE 0.1875", .2500", .3125", .3750", .4375", .500. Each hole size marked with the corresponding Boeing Part number 186A-186F Includes Test Report and Certific... | 1 | |
| 203026-101 | TGB BEVEL GEAR - REFERENCE STANDARD, CALIBRATION RING EWR | 1 | |
| 204-94034-1 | Boeing Reference Standard- Lower Lug APE-1 Primary , D204-12769-6 ASIP Inspection Program. Material: 4340 Steel. Includes Test Report and Certificate of Conformance. | 1 | |
| 208 FRONT SPAR | CESSNA / TEXTRON AVIATION EDDY CURRENT REFERENCE STANDARD 208 FRONT SPAR LOWER CAP. Drawing NO. 2683201 | 1 | |
| 208 REAR SPAR | CESSNA / TEXTRON AVIATION EDDY CURRENT REFERENCE STANDARD 208 REAR SPAR LOWER CAP. Drawing NO. 2683202 | 1 | |
| 29A028 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601. MATERIAL: 4340 STEEL. 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance..... | 4 | |
| 29A032 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601, MATERIAL: 6AL-4V TITANIUM, 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 3 | |
| 29A047 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601, Aluminum(7075-T7)(39.5% IACS) 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 5 | |
| 29A120 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601, MAGNESIUM. 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 2 | |
| 31A008 | AIRBUS REFERENCE STANDARD 51-63-01 PT 6 FIG 601. MATERIAL: 4340 STEEL. 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance... | 1 | |
| 412B5MHZ35R80FE | CUSTOM 5MHz 35° TRANSVERSE WAVE TRANSDUCER WITH END MOUNT MICRODOT CONNECTOR WIT A 80mm RADIUS. USED WITH AIRBUS REFERENCE STANDARD PART NUMBER 98A54003096 Includes Test Report and Certificate of Conformance. REFERENCE: AIRBUS A300-600 PART 4 54-50-20 | 1 | |
| 412B5MHZ40R75FE | CUSTOM 5MHz 40° TRANSVERSE WAVE TRANSDUCER WITH END MOUNT MICRODOT CONNECTOR WIT A 75mm RADIUS. USED WITH AIRBUS REFERENCE STANDARD PART NUMBER 98A54003069 Includes Test Report and Certificate of Conformance. REFERENCE: AIRBUS A300-600 PART 4 54-50-20 | 1 | |
| 412E5MHZ60FE | CUSTOM 5MHz 60° IN FE TRANSVERSE WAVE BACKSHOOTING TRANSDUCER WITH A SIDE MOUNTED MICRODOT CONNECTOR. CASE SIZE: .690" x .354" x .354 Includes Test Report and Certificate of Conformance. REFERENCE STANDARD: 98A54003077 | 1 | |
| 53-20-165/2 | RADIUSED ULTRASONIC PROBE SHOE USED WITH K5K AND REFERENCE STANDARD 53-20-165/1 (BAe 146 Series) | 1 | |
| 53-20-171/2 | RADIUSED ULTRASONIC PROBE SHOE USED WITH K5K(AFC-525-7S) AND REFERENCE STANDARD 53-20-165/1 (BAe 146 Series). Includes Certificate of Conformance. | 1 | |
| 55-36-01 | UT CALIBRATION REFERENCE STANDARD , STEP WEDGE, 7000 SERIES ALUMINUM, GENERIC AS PER ATR 72 NTM 55-36-01 | 1 | |
| 6AL-6V-2SN-Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" +/-.001 DEEP, (MAX WIDTH .005"), 6AL-6V-2SNTi | 1 | |
| 71658-18-53/2&3 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 CARBON STEEL, 54-10-11 PAGE 651 FIG.603 SHEET 39 | 1 | |
| 71658-7-35/1&4 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 CARBON STEEL, 54-10-11 PAGE 651 FIG.603 SHEET 39 | 1 | |
| 717RS10-C | 717-200 REFERENCE STANDARD FOR THE LOWER CENTER WING SKIN PANELS AT STRINGER 16 &18. PAGES 1-11. MATERIAL: 2024-T3, 7075-T6 &7075-T7 ALUMINUM. Includes Test Report and Certificate of Conformance. | 1 | |
| 7637987-19 | CUSTOM SPO-2664 SLIDING PROBE FIXTURE USED WITH DC-10 REFERENCE STANDARD 7637987-15 Includes Certificate of Conformance | 1 | |
| 98S53805002-000 | ATR REFERENCE STANDARD 53-61-18 PT 6 FIGURE 603 PAGE 609. INSPECTION OF REAR PRESSURE BULKHEAD PERIPHERY OF DOME SKIN AND CONNECTION WITH VERTICAL FLANGE OF DOME VERTICLAL CHORD. Includes Test Report traceable to NIST and Certificate of Conformance. | 6 | |
| 98S57205030-004 | COMPOSITE LIGHTNING REFERENCE STANDARD..FOR ATR72 PT 4 51-40-00: REFERENCE DRAWING | 5 | |
| 98S57205030.001 | COMPOSITE LIGHTNING REFERENCE STANDARD..FOR ATR72 PT 4 51-40-00: REFERENCE DRAWING | 4 | |
| 98S57205030.004 | COMPOSITE LIGHTNING REFERENCE STANDARD..FOR ATR72 PT 4 51-40-00: REFERENCE DRAWING | 5 | |
| 99A51107299001 | AIRBUS REFERENCE STANDARD (WIFI BROADBAND) | 5 | |
| 99A57004101000-MOD | AIRBUS REFERENCE STANDARD WITH CERTIFICATE | 1 | |
| 99A57204403000 | AIRBUS REFERENCE STANDARD (WING INSPECTION) | 3 | |
| 99A57204403001 | AIRBUS REFERENCE STANDARD (WING INSPECTION) | 5 | |
| 99D51107295000 | AIRBUS REFERENCE STANDARD (WIFI BROADBAND) | 5 | |
| 99D51307001000 | AIRBUS REFERENCE STANDARD (WIFI BROADBAND) | 1 | |
| 99D51407291001 | AIRBUS CARBON LAMINATE THICKNESS REFERENCE STANDARD SET A318-A321 51-10-06-PB4 Multidirectional Fabric Material, BLOCKS 01-06 includes waterproof case. Nominal Thicknesses of 1mm, 3mm, 5mm, 9mm, 15mm, 19mm. Includes Test Report and Certificate of Con... | 7 | |
| 99D57103009000 | AIRBUS REFERENCE STANDARD. MATERIAL: 7175-T7 ALUMINUM ANODIZED. PAINT WITH PRIMER | 4 | |
| 99D57103011000 | Airbus Reference Standard w/Certs | 5 | |
| 99D57103014000 | AIRBUS REFERENCE STANDARD W/CERTS | 5 | |
| 99D57103020000 | Airbus Reference Standard w/certs | 3 | |
| 99D7204125000 | Airbus/FIL/EDSWNU/0824Reference Standard | 1 | |
| 99F53303113000 | AIRBUS REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM. 2 CORNER EDM SLOTS: 3mm x 3mm(.120" x .120") x 0.3mm(.012") Wide. Paint with primer. Includes Test Report and Certificate of Conformance. | 1 | |
| 99F53303115000 | AIRBUS REFERENCE STANDARD A330 53-30-54 PAGE 6. US INSPECTION OF FUSELAGE INTERNAL STRUCTURE, SKIN PANEL JUNCTION WITH FR53.2 BULKHEAD FWD FACE BETWEEN STR39 AND STR42. Includes Test Report and Certificate of Conformance. | 3 | |
| 99F57103041000 | AIRBUS REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM WITH PROTECTIVE FINISH 13-002 and PAINT PRIMER 16-006. Includes Test Report and Certificate of Conformance(COC) | 2 | |
| 99F57103042001 | AIRBUS REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM WITH PROTECTIVE FINISH 13-002 and PAINT PRIMER 16-006. APPLY TOP COAT 16-008. Includes Test Report and Certification of Conformance(COC) | 2 | |
| 99F57103051000 | AIRBUS REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM WITH PROTECTIVE FINISH 13-002 and PAINT PRIMER 16-006. APPLY TOP COAT 16-008 | 1 | |
| 99F57103059000 | AIRBUS REFERENCE STANDARD 57-11-68-991-007-A. MATERIAL: 7175 or 7075 ALUMINUM WITH PROTECTIVE FINISH 13-002 and PAINT PRIMER 16-006. Includes Test Report and Certificate of Conformance. | 1 | |
| 99F57204173000 | AIRBUS A330 REFERENCE STANDARD 57-20-46-270-801-A-01 PAGE 12. OUTER WING REAR SPAR UPPER & LOWER FLANGES BETWEEN RIB7 and RIB12 LH/RH. MATERIAL: 7010 ALUMINUM. Includes Test Report and Certificate of Conformance. | 3 | |
| 99F57204174000 | AIRBUS REFERENCE STANDARD A330 57-20-46-991-005-A PAGE 13. US INSPECTION OF OUTER WING REAR SPAR FWD FACE BETWEEN RIB 7 AND RIB 12 INCLUDING TOP AND BOTTOM FLANGES Includes Test Report and Certificate of Conformance. | 2 | |
| 99F57204175000 | AIRBUS REFERENCE STANDARD A330 57-20-46-991-005-A PAGE 13. US INSPECTION OF OUTER WING REAR SPAR FWD FACE BETWEEN RIB 7 AND RIB 12 INCLUDING TOP AND BOTTOM FLANGES Includes Test Report and Certificate of Conformance. | 2 | |
| 99F57204176000 | AIRBUS REFERENCE STANDARD A330 57-20-46-991-005-A PAGE 13. US INSPECTION OF OUTER WING REAR SPAR FWD FACE BETWEEN RIB 7 AND RIB 12 INCLUDING TOP AND BOTTOM FLANGES Includes Test Report and Certificate of Conformance. | 2 | |
| 99F57204177000 | AIRBUS REFERENCE STANDARD A330 57-20-46-991-005-A PAGE 13. US INSPECTION OF OUTER WING REAR SPAR FWD FACE BETWEEN RIB 7 AND RIB 12 INCLUDING TOP AND BOTTOM FLANGES Includes Test Report and Certificate of Conformance. | 2 | |
| 99T045-1 | Western Global Airlines LFEC Satcom Antenna Cutout Reference Standard, Appendix 1 (Sheet 1). Material: 2024-T3 Clad Aluminum. Includes Test Report and Certificate of Conformance. | 1 | |
| ACWM-E175-IB | Inner Wheel Standard, Embraer..175 90000582: 1. Contains a Total of 3 EDM Flaws in the Bead Seat Area of the Reference Standard. Flaw sizes: 1.52mm Long x 0.76mm Deep x 0.10mm Wide Tolerance= +/- 0.05mm. Includes Test Report and Certificate of Confor... | 1 | |
| ACWM-E175-OB | Outer Wheel Standard, Embraer..175 90000582-1. Contains a Total of 3 EDM Flaws in the Bead Seat Area of the Reference Standard. Flaw sizes: 1.52mm Long x 0.76mm Deep x 0.10mm Wide Tolerance= +/- 0.05mm. Includes Test Report and Certificate of Conform... | 1 | |
| AF- 4120 | LOW FREQUENCY RING PROBE, 10KHZ-100KHZ, REFLECTION, .405"ID, .800"OD, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. INCLUDES TEST REPORT AND CERTIFICATE OF CONFORMANCE. USED WITH REFERENCE STANDARD: NDT1102-100 TI | 1 | |
| AF-4041 | LOW FREQUENCY DIFFERENTIAL PROBE , 1-40KHZ. Maximum height of .50" inches and diameter of .300" to .320" inches. Flat at the end. Used with ANDT3016-B reference standard. Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4041/4F | LOW FREQUENCY DIFFERENTIAL PROBE , 1-40KHZ. Maximum height of .50" inches and diameter of .300" to .320" inches, 4 Pin Fischer Connector. Flat at the end. Used with ANDT3016-B reference standard. Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4084 | LOW FREQUENCY REFLECTION RING PROBE, 800HZ-10KHZ, .320"Ø ID,.600"Ø OD x .700"H, WITH TRIAX FISCHER CONNECTOR. REFERENCE: 767 PART 6 53-10-22, NDT6075 REFERENCE STANDARD. Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4092 | LOW FREQUENCT RING PROBE, 500Hz-3KHz. REFLECTION, 1.00" OD, .510" ID, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. For Reference Standard NDT3255 | 1 | |
| AF-4101 | LOW FREQUENCT RING PROBE, 1-10KHz. REFLECTION, .700" OD, .350" ID, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. For Reference Standard NDT3255 | 1 | |
| AF-4102 | LOW FREQUENCT RING PROBE, 50Hz-5KHz. REFLECTION, .700" OD, .350" ID, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. For Reference Standard NDT3255 | 1 | |
| AF-4109/TI | LOW FREQUENCY REFLECTION RING PROBE, ID .470, OD.900, 3-10KHZ. For reference standard NDT 3259. Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4120 | LOW FREQUENCY RING PROBE, 10KHz-100KHz, REFLECTION, .405"ID, .800"OD, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. USED WITH REFERENCE STANDARD: NDT1102-100 Ti | 1 | |
| AF-4124/300H | REFLECTION RING PROBE TRIAX FISHER CONNECTOR, 1.25"OD .75" ID(19.6mm) 300HZ-1KHZ. 737 PART 6 57-10-53, pg.2, USED WITH REFERENCE STANDARD NDT3168 AND NDT3176-X. Includes test report and Certificate of Conformance. | 1 | |
| AF-4125/100H | CUSTOM REFLECTION RING PROBE 1.2" OD, .605" ID, 50Hz-3KHz TRIAX FISHER CONNECTOR. 737 PART 6 57-10-58, pg.2. and 737 PART 6 57-10-54, pg.2 USED WITH NDT3153-X AND 3167-X SERIES REFERENCE STANDARDS. Includes Test Report and Certificate of Conform... | 1 | |
| AF-4144 | LOW FREQUENCY DIFFERENTIAL PROBE , 1-40KHZ. Maximum height of .50" inches and diameter of .300" to .320" inches. 10 inches long Flat at the end. Used with ANDT3016-B reference standard. Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4153/TI | LOW FREQUENCY RING PROBE 1-15KHz, REFLECTION, ID.565" OD.910",SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes Test Report and Certificate of Conformance. For Reference Standard NDT 3225. | 1 | |
| AF-4202 | LOW FREQUENCY REFLECTION RING PROBE, 500HZ-5KHZ, ID 0.325", OD 0.790" (MAX). 1.05" HEIGHT. TRIAX FISCHER CONNECTOR. USED WITH NDT6097 REFERENCE STANDARD Includes Test Report and Certificate of Conformance. | 1 | |
| AF-4334 | Low Frequency Reflection Ring Probe, 40Hz-500Hz. 1.3"Ø I.D. 2.0"Ø O.D., supplied with a Triax Fischer Connector. REFERENCE STANDARD: NDT7035. Includes test report and Certificate of Conformance. | 1 | |
| AF-4335 | LOW FREQUENCY REFLECTION RING PROBE, 300Hz-1KHz .425"Ø ID SUPPLIED WITH A TRIAX FISCHER CONNECTOR. Includes test report and Certificate of Conformance.....USED WITH 717-200 REFERENCE STANDARD P/N: 717RS10-C | 1 | |
| AF-5272 | CUSTOM COUNTERBORE ROTARY ADJUSTABLE X STYLE PROBE WITH THE COIL LOCATED AT THE EDGE OF THE PROBE TIP, .936'-1.0" 2.0"WL, SUPPLIED WITH A 4 PIN FICHER CONNECTOR, 100 KHz-2MHz Includes Test Report and Certificate of Conformance REFERENCE STANDARD - NDT3117 | 1 | |
| AF-5278/TF | HIGH FREQUENCY SURFACE PROBE, Twin Coil Differential 50-500KHZ. 4.0" Long 0.375" Diameter with Triax Fischer connector. For use with Boeing Reference Standard 497 767 Part 6 53-00-04. IncludesTest Report and Certificate of conformance. | 1 | |
| AFHS20-2A-5 | Aluminum Multi-hole reference standard with certificate. Contains 20 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 1.0" inch. Each hole contains two EDM corner... | 1 | |
| AFK-1002 | CUSTOM BRITISH AIRWAYS KIT 1. Contains one each of Boeing 1002 Reference Standard, ATPN-92-12.5FX , ATPN-93-5B, ABNC-MD6, in a waterproof storage case. Includes test reports and Certificate of Conformance. | 1 | |
| AFK-1011 | CUSTOM BRITISH AIRWAYS KIT 2. Contains one each of Boeing 1004 Reference Standard, ATPN-92-12.5FX , ATPN-93-5B, ABNC-MD6, in a waterproof storage case. Includes test reports and Certificate of Conformance. | 1 | |
| AFK-1014 | Custom Ultrasonic Kit, PART 4 53-10-13 for the WING REAR SPAR - STA 663.75 REAR SPAR BULKHEAD SIDE FRAME FITTING FAIL SAFE STRAP. Kit includes 1 of each AFM-560AT & AFS-0541 Transducers, 1 NDT3312 Reference Standard and 1 ABNC-MD6. Supplied with a waterpr | 1 | |
| AFK-1016 | CUSTOM BRITISH AIRWAYS KIT 3. Contains one each of Boeing 1005 Reference Standard, ATPN-92-12.5FX , ATPN-93-5B, ABNC-MD6, in a waterproof storage case. Includes test reports and Certificate of Conformance. | 1 | |
| AFK-1017 | Custom Eddy Current Inspection Kit. Includes the following probes, Reference Standard and cables.AUR-.125SE/1.75WL-LF, AUR-.156SE/1.75WL-LF, AUR-.187SE/1.75WL-LF, AUR-.250SE/2.0WL-LF, AUR-.312SE/2.0WL-LF, AUR-.375SE/2.0WL-LF, AUR-.437SE/2.0WL-LF, AUR-... | 1 | |
| AFNDT-1000/4340 | 12 HOLE REFERENCE STANDARD 4340 STEEL WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000/SA | 12 HOLE REFERENCE STANDARD ALUMINUM WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000SA-1 | 12 HOLE REFERENCE STANDARD ALUMINUM WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000SS | 12 HOLE REFERENCE STANDARD STAINLESS STEEL WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1000TI | 12 HOLE REFERENCE STANDARD 6AL4V WITH A .020" MID WALL NOTCH, .030" CORNER NOTCH, .050" CORNER NOTCH, .010" ,.020", .040: .050" SURFACE NOTCH. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1002 | CUSTOM 3 HOLE 7075-T6 ALUM. EC REFERENCE STANDARD WITH a .020x.020" CORNER NOTCH IN EACH HOLE. HOLE SIZES 1.063", .687", .625" DIA. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1025AL | Multi-Hole reference standard. Material: 7075-T6 Aluminum. 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" .020" x .020" x .005" Wide ± .002" Through EDM Notches in each hole. Standard also includes 3 surface EDM n | 1 | |
| AFNDT-1025TI | Multi-Hole reference standard. Material: 6Al-4v Titanium. 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" .020" x .020" x .005" Wide ± .002" Through EDM Notches in each hole. Standard also includes 3 surface EDM no | 1 | |
| AFNDT-1080/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES 0.5mm, 1.0mm, 2.0mm, 3.00mm, 4.0mm, 5.0mm (.004"W +/- .002, MAX.006), 4340 STEEL 1.0"W x 7.0"L. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2006/300M | 12 HOLE REFERENCE STANDARD 300M STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEEP .005" ... | 1 | |
| AFNDT-2006A | 12 HOLE REFERENCE STANDARD 7075-T6 aluminum. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.004" ±.002" WIDE CORNER EDM NOTCH in EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020",... | 1 | |
| AFNDT-2006S | 12 HOLE REFERENCE STANDARD 4130 or 4340 STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEE... | 1 | |
| AFNDT-2006SS | 12 HOLE REFERENCE STANDARD 304 304 STAINLESS STEEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040... | 1 | |
| AFNDT-2006TI | 12 HOLE REFERENCE STANDARD 6AL-4V.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005"WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020", .040" DEEP .005" WIDE... | 1 | |
| AFNDT-2010AL | Custom McDonnell Douglas 15 bolt hole reference standard with a .060"L x .030Dx .005" max width mid-wall notch, and .030"x.030"x.005" max width corner notch in each hole. Hole sizes (.156", .172", .188", .203", .250", .266", .281", .297", .313", .328"... | 1 | |
| AFNDT-2013AL | 12 HOLE REFERENCE STANDARD 7075-T6 (3/16" x 2), 13/64", 7/32", 15/64" ,(1/4" x 2 ), 17/64",9/32", 19/64",5/16", 21/64" .020"x.020" and .030"x.030" x .005"W +/-.002" CORNER EDM NOTCH PER BOEING SPECIFICATION 747 PART 6 51-00-00 PAGE 8 FIGURE 3. Includes Te | 1 | |
| AFNDT-2030/13-8 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/13-8PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH MO STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-7PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-7PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2014-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2014-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2014-T651 | DDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2014-T651 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/300M | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: 300M STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/301 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), CRES 301 1/2 HARD(MIL-S-5059) 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304L | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304L STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/316SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 316 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4130 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4130 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/6061-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002), 6061-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-2030/7075-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/7075-T7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/718 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 718 INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/I600 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 600 SERIES INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/MAG | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| AFNDT-2030/MAR | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002). MATERIAL: 250 MARAGING STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/N200 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: NICKEL 200. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX .006"), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and COC | 1 | |
| AFNDT-2030CS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), 4130 or 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2035 | 6 Hole reference standard (Aluminum 7075-T6 with certifications). Hole Sizes: 1.0", 1.125", 1.250" ,1.500", 1.625", 1.750", ( .030 x .030 x .006 +/- .001) Corner EDM Notches and .010, .020, .040 Surface notches).. Includes Test Report and Certificate | 1 | |
| AFNDT-2042/AL | CUSTOM 5 HOLE REFERENCE STANDARD MADE OF 7075-T6 ALUMINUM WITH (0.5mm X 0.5mm +/- .05mm) CORNER EDM FLAWS. HOLE SIZE : 13/64", 19/64", 23/64", 7/16" & 31/64". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2054AL-2 | CUSTOM ALUMINUM REFERENCE STANDARD PER BOEING SPECIFICATION NDT1016-NDT1021, 737, 747, 757, 767 PT 6 51-00-16 FIG 16, 777 PT 6 51-00-02 PROCEDURE 3, 787 PT 6 51-00-02 PROCEDURE 1. WITH HOLE DIAMETERS: .125" .156", .187", .250",.375",.500". CORNER... | 1 | |
| AFNDT-2064/AL | SAFRAN MESSIER-BUGATTI-DOWTY ET SURFACE REFERENCE STANDARD 32-09-01 FIGURE 67,GRAPHIC-32-09-01-041-008-A01. MATERIAL: 2024-T351 ALUMINUM. Includes Test Report and Certificate of conformance. | 1 | |
| AFNDT-2064/MAG | SAFRAN MESSIER-BUGATTI-DOWTY REFERENCE STANDARD 32-09-01 MAGNESIUM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2064/TI | SAFRAN MESSIER-BUGATTI-DOWTY REFERENCE STANDARD 32-09-01 6AL-4V TITANIUM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2066/TI | 12 HOLE REFERENCE STANDARD 6AL-4V TITANIUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .001" WIDE THRU NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and C | 1 | |
| AFNDT-2066A | 12 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .001" WIDE THRU NOTCH. .008", .020", .040" SURFACE NOTCHES. .005" +/-.001". Includes Test Report and | 1 | |
| AFNDT-2073AL | 12 HOLE REFERENCE STANDARD 7075-T6 aluminum. Hole Sizes: 25/64(.390), 13/32(.406), 27/64(.421),7/16(.437), 29/64(..453), 15/32(..468), 31/64(.484),1/2(.500), 33/64(.515),17/32(.531), 35/64(.546), 9/16(.562). EDM NOTCH: .030" X. 030" x.005" ±.001" WIDE... | 1 | |
| AFNDT-2073TI | 12 HOLE REFERENCE STANDARD 6AL-4V Titanium. Hole Sizes: 25/64(.390), 13/32(.406), 27/64(.421),7/16(.437), 29/64(..453), 15/32(..468), 31/64(.484),1/2(.500), 33/64(.515),17/32(.531), 35/64(.546), 9/16(.562). EDM NOTCH: .030" X. 030" x.005" ±.001" WIDE ... | 1 | |
| AFNDT-2074 | CUSTOM SURFACEREFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .007" MAX WIDTH. MATERIAL: 7075-T6 ALUMINUM. SIZE: 4.0 x 1.5 x .25". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-2076AL | 10 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. Hole Sizes: 1/8", 5/32", 3/16", 7/32" ,1/4", 9/32", 5/16", 3/8", 7/16", 1/2", .030" X. 030" x.005" +/- .001" WIDE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2076TI | 10 HOLE REFERENCE STANDARD 6AL-4v TITANIUM. Hole Sizes: 1/8", 5/32", 3/16", 7/32" ,1/4", 9/32", 5/16", 3/8", 7/16", 1/2", .030" X. 030" x.005" +/- .001" WIDE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/6AL4V | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2109 | 15 Hole aluminum reference standard, material 7075-T6, hole sizes: 1/8, 5/32, 11/64, 3/16, 13/64, 7/32, 15/64, 1/4, 17/64, 9/32, 19/64, 5/16, 21/64, 11/32, 23/64. With .030 x .030 and .020 x .020 Corner EDM Notches. Includes Test Report and Certificat | 1 | |
| AFNDT-2114AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.006W +/- .001). BLOCK SIZE:3.156 "L x 1.375"W x .312"H. MATERIAL: 2024-T3 ALUMINUM.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2127 | SAFRAN MESSIER -BUGATTI-DOWTY REFERENCE STANDARD Material aluminum 7075-T6; Thickness 1/2". - Number of holes 5;- hole diameter 9/16 in, 10/16 in, 11/16 in, 12/16 in, 13/16 in; EDM notch in each hole: thru the thickness, depth and width in according with | 1 | |
| AFNDT-2132/2024-T3 | 20 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8, 5/32, 11/64, 3/16, 13/64, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 17/32, 9/16, 5/8, 11/16, 3/4. TOTAL OF 20 CORNER EDM NOTCHES .030 x .030 x .005 +/-.001. MID-WALL EDM NOTC | 1 | |
| AFNDT-2132/7075-T6 | 20 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8, 5/32, 11/64, 3/16, 13/64, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 17/32, 9/16, 5/8, 11/16, 3/4. TOTAL OF 20 CORNER EDM NOTCHES .030 x .030 x .005 +/-.001. MID-WALL EDM NOTC | 1 | |
| AFNDT-2136 | 12 HOLE REFERENCE STANDARD 6061-T6. HOLE SIZES: 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4". .030" x .030" x .005" +/- .001" W CORNER NOTCH IN EACH HOLE. SURFACE NOTCHES: .008", .020", .040" . .005" +/-.001". Includ | 1 | |
| AFNDT-2140/304L | 11 HOLE REFERENCE STANDARD IN 304L STAINLESS STEEL; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), WITH .030"x.030" CORNER EDM NOTCH IN EACH HOLE.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2140/4130 | 11 HOLE REFERENCE STANDARD IN 4130 CARBON STEEL; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16,5/8,11/16, 3/4), WITH .030"x.030" CORNER EDM NOTCH IN EACH HOLE.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2140/6AL4V | 11 HOLE REFERENCE STANDARD IN 6AL-4v Ti; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), WITH .030"x.030" CORNER EDM NOTCH IN EACH HOLE.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2140/7075 | 11 HOLE REFERENCE STANDARD IN 7075-T6 ALUMINUM; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), WITH .030"x.030" CORNER EDM NOTCH IN EACH HOLE.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2141AL | 12 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .030" x .030" CORNER EDM NOTCH and .020" MID-WALL EDM NOTCH IN EACH HOLE. Tolerance: .005" +/-.001". Includes Test Repo | 1 | |
| AFNDT-2144 | 13 HOLE REFERENCE STANDARD 7075-T6 Auminum. Hole Sizes: (5/32",3/16", 7/32" ,1/4", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 1.0"), . 040" DEEP x .005" WIDE +0.00/-.002" THROUGH EDM NOTCH in EACH HOLE. Includes Test Report and Certificate of Co | 1 | |
| AFNDT-2149AL | 13 HOLE REFERENCE STANDARD 7075-T7 Auminum. Hole Sizes: (5/32",3/16", 7/32" ,1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1.0"), . 020" DEEP x .005" MAX WIDTH THROUGH EDM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2149AL-1 | 13 HOLE REFERENCE STANDARD 7075-T7 Auminum. Hole Sizes: (5/32",3/16", 7/32" ,1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1.0"), . 040" DEEP x .005" MAX WIDTH THROUGH EDM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2149SS | 13 HOLE REFERENCE STANDARD 304 Stainless Steel. Hole Sizes: (5/32",3/16", 7/32" ,1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1.0"), . 020" DEEP x .005" MAX WIDTH THROUGH EDM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2150AL | 9 HOLE REFERENCE STANDARD 7075-T6, HOLE SIZES, 3/16",, 7/32" , 9/32", 5/16, 11/32", 3/8", 7/16", 5/8", 3/4", CORNER EDM NOTCH .030X.030 +/- 10%; WIDTH: .005+/-.001. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2151AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.005"W + .001"), MATERIAL: 5086 H32 ALUMINUM. (29.0% IACS. SIZE: 80mm(3.15") L +5mm(.197") x 30mm(1.18") W +5mm(.197") x 8mm(.315") THICK +3mm(.118"). Includes Mill Certifica... | 1 | |
| AFNDT-3001 | Embraer 170 reference standard with a .473" diameter hole. Per NDTM PT1 51-00-00-916-802-A , 1.4mm x 1.4mm +/-.05mm long x 0.1mm +/-.05 wide corner EDM notch. Material: 7050-T7 Aluminum. Block size 2.0" x 2.0" x .375". Includes Test Report and Certifica | 1 | |
| AFNDT-3007 | SURFACE NOTCH REFERENCE STANDARD 15-5 PH STEEL. EDM NOTCH SIZE: FULL WIDTH OF PART x .20mm(.008") WIDE x .50mm(.020") DEEP +/- .05mm(.002"). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3015 | EMBRAER 170/190 SERIES EDDY CURRENT SURFACE REFERENCE STANDARD 50-00-00 PT 1 PAGE 4, Aluminum(7075-T6) 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3024AL | 12 HOLE REFERENCE STANDARD. MATERIAL: 2024-T3 ALUMINUM. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X .030" X .005" +/- .001" WIDE CORNER EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG . | 1 | |
| AFNDT-3026AL | EDDY CURRENT SURFACE REFERENCE STANDARD Leonardo Helicopters SB No. 109EP-158. MATERIAL: 7475-T7 ALUMINUM. SIZE: 1.0" x 3.0" x .25" EDM SLOT (0.5mm DEEP) x (0.05-0.25mm WIDE) +/-.03mm. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3027AL | MHS style Multi-Hole reference standard (Aluminum 7075-T6 with certifications). 12 Holes 3/16", 7/32", 1/4" ,9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16" ( .030 x .030 x .006 +/- .001) Corner Notches and .010, .020, .040 Surface notch... | 1 | |
| AFNDT-3028AL | 3i-Hole reference standard (Aluminum 7075-T6 with certifications). Hole Sizes , 7/16", 1/2" and 11/16" ( .030 x .030 x .006 +/- .001) Corner Notches. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3032 | 3 HOLE 100° COUNTERSINK REFERENCE STANDARD 2024-T3 ALUMINUM, PLATE SIZE: 3.0" x 2.0" x 1/4" . HOLE SIZES: 5/32", 3/16" and 1/4" TOTAL OF 3 EDM NOTCHES .040" +0.004"/-0.000" Long x .007" Max Width Through the Depth of the Countersink. | 1 | |
| AFNDT-3032-1 | 3 HOLE 100° COUNTERSINK REFERENCE STANDARD 7075-T6 ALUMINUM, PLATE SIZE: 3.0" x 2.0" x 1/4" . HOLE SIZES: 3/16", 7/32" and 1/4" TOTAL OF 3 CORNER EDM NOTCHES: .030" +0.004"/-0.000" Long x .007" Max Width Through the Depth of the Countersink. Includes Tes | 1 | |
| AFNDT-3034AL | Custom Bolt Hole / Countersink Reference Standard Combination Containing 6 Bolt Hole Sizes of .171", .218", .281", .343", .406", .500". EDM Slot Size: .030" x .030" x .005" Wide +/- .001". 5 Holes with 100° Countersinks, Hole Sizes: .218", .312", .37... | 1 | |
| AFNDT-3035SS | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM NOTCHES: .005", .010", .020", .060" (.005"W +/- .002, MAX.007" WIDE). MATERIAL: 301 1/2 HARD STAINLESS STEEL(MIL-S-5059) 1.0"W x 4.0"L x .125", NOTE: .750" DISTANCE BETWEEN EACH NOTCH. Includes Test Repor... | 1 | |
| AFNDT-3036AL | CUSTOM 2 HOLE EDDY CURRENT REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. HOLE SIZES: .250" and .875" WITH a .030" x .030" x .007" MAX WIDTH CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3037 | CUSTOM EDDY CURRENT HOLE REFERENCE STANDARD. MATERIAL: 718 INCONEL. HOLE SIZE: .256"Ø WITH a 0.1" x 0..1" x .010" +/- .002" EDM NOTCH IN THE BOTTOM RADIUS OF THE HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3051AL | (Aluminum Multi-hole reference standard with certificate. Contains 2 rows of 6 hole sizes. The first row has no flaws or side drilled holes. The second row includes side drilled holes. Hole Sizes: 3/16", 1/4", 5/16", 3/8", and 1/2". Material: 7075-T6 ... | 1 | |
| AFNDT-3052AL | (Aluminum Multi-hole reference standard with certificate. Contains 2 rows of 29 hole sizes. The first row has no flaws or side drilled holes. The second row includes side drilled holes. Hole Sizes: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32"... | 1 | |
| AFNDT-3055 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4330 STE... | 1 | |
| AFNDT-3056AL | 10 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. Hole Sizes: 3/16", 7/32" ,1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16', 5/8". Corner EDM Notches: .020" x .020" x .005" +/- .001" Wide and Mid-Wall EDM Notches .020" x .020" x .005" +/- .001" Wide in Each... | 1 | |
| AFNDT-3058/INC | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .5mm, 1.0mm, 2.0mm x (.006"Wide +/- .001). MATERIAL: 718 Inconel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3058SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES: 0.5mm, 1.0mm, 2.0mm x (.005"Wide + .000/-.002). MATERIAL: 304 Stainless Steel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3061AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3071 | Custom designed eddy current multi-layer aircraft aluminum skin test specimen, drawing 2, sheets 1-4. reference standard for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3104 | The VMA.01-0-07 reference standard is ..3 ½” long x 3.0” wide x 1/4” thick...• The tapered notch on both standards is 0.080” deep at the edge of the standard and tapers to 0.000” deep...• The tapered notch has scribe marks every 0.010” deep from 0.000”... | 1 | |
| AFNDT-3114 | 16 HOLE REFERENCE STANDARD 6AL-4V TITANIUM. 2 OF EACH HOLE SIZES: 3/16", 13/64" 7/32" , 1/4", 17/64", 9/32", 7/16", 9/16". .030" x .030" CORNER NOTCH IN 1st HOLE SET and .060" x .020" MID-WALL NOTCH IN 2nd HOLE SET. Tolerance: .006" +/-.001". Includ... | 1 | |
| AFNDT-3115 | 16 HOLE REFERENCE STANDARD 4340 CRES STEEL. 2 OF EACH HOLE SIZES: 3/16", 13/64" 7/32" , 1/4", 17/64", 9/32", 7/16", 9/16". .030" x .030" CORNER NOTCH IN 1st HOLE SET and .060" x .020" MID-WALL NOTCH IN 2nd HOLE SET. Tolerance: .006" +/-.001". Includ... | 1 | |
| AFNDT-3116 | 16 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM. 2 OF EACH HOLE SIZES: 3/16", 13/64" 7/32" , 1/4", 17/64", 9/32", 7/16", 9/16". .030" x .030" CORNER NOTCH IN 1st HOLE SET and .060" x .020" MID-WALL NOTCH IN 2nd HOLE SET. Tolerance: .006" +/-.001". Inclu... | 1 | |
| AFNDT-3121S | 10 hole Reference Standard 4340 or 4130 Carbon Steel. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .030" x .030" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", ... | 1 | |
| AFNDT-3122T-0 | 10 hole Reference Standard 6AL-4v Titanium. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .030" x .030" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", .040" Dee... | 1 | |
| AFNDT-3122T-4 | 10 hole Reference Standard 6AL-4v Titanium. Contains 10 hole sizes; 1/8, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4 inch diameters.( .050" x .050" +/- 10% x .006" +/- .001" Wide Corner EDM Notch and 3 Surface EDM Notches at .010", .020", .040" Dee... | 1 | |
| AFNDT-3139AL | 11 HOLE REFERENCE STANDARD in 7075-T6 Aluminum; Hole Sizes: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), With a .020" x .020" x .005" and a .030"x.030" x .005" +/-.002" Corner EDM Notch in each hole Per BOEING Proceedure 51-00-16 PT 6... | 1 | |
| AFNDT-3139CS | 11 HOLE REFERENCE STANDARD in 4130 Carbon Steel; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16,5/8,11/16, 3/4), With a .020" x .020" x .005" and a .030"x.030" x .005" +/-.002" Corner EDM Notch in each hole Per BOEING Proceedure 51-00-16 PT 6... | 1 | |
| AFNDT-3139TI | 11 HOLE REFERENCE STANDARD in 6AL-4V Titanium; Hole Sizes: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), With a .020" x .020" x .005" and a .030"x.030" x .005" +/-.002" Corner EDM Notch in each hole Per BOEING Proceedure 51-00-16 PT 6 ... | 1 | |
| AFNDT-3140AL | 7 HOLE REFERENCE STANDARD in 7075-T6 Aluminum; Hole Sizes: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2), With a .020" x .020" x .005" and a .030"x.030" x .005" +/-.002" Corner EDM Notch in each hole Per BOEING Proceedure 51-00-16 PT 6 FIG 3, 14 Notches Tota... | 1 | |
| AFNDT-3141AL | Custom McDonnell Douglas 12 bolt hole reference standard 7075-T6 Aluminum with a .060"L x .030Dx .005" max width mid-wall notch, and .030"x.030"x.005" max width corner notch in each hole. Hole sizes (.125, .156", .187", .250", .281", ..312", .375", .4... | 1 | |
| AFNDT-3141AL-1 | Custom McDonnell Douglas 12 bolt hole reference standard 7075-T6 Aluminum with .005" max width through EDM notch in holes #1-#6 and a .060"L x .030"D x .005" max width mid-wall notch in holes #7-12, and .030"x.030"x.005" max width corner notch in each hol | 1 | |
| AFNDT-3141AL-2 | Custom McDonnell Douglas 12 bolt hole reference standard 7075-T6 Aluminum with a .060"L x .030Dx .005" max width mid-wall notch, and .030"x.030"x.005" max width corner notch in each hole. Hole sizes (.2966, .3122", .3278", .3434", .359", ..3746", .3902", | 1 | |
| AFNDT-3146AL | 12 hole Reference Standard. Hole sizes: 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8 and 3/4 inch diameters, .030" x .030" x .005" +/-.002" Wide Corner EDM Notches and .020" x .020" x .005" +/-.002" Wide Mid-Wall EDM Notches. Materia... | 1 | |
| AFNDT-3147AL | 7 HOLE 100° COUNTERSINK REFERENCE STANDARD 2024-T3 ALUMINUM, PLATE SIZE: 3.0" x 2.5" x 3/8" . HOLE SIZES: 5/32", 3/16", 7/32",1/4", 5/16",3/8", 7/16". TOTAL OF 7 EDM NOTCHES .030" +0.002"/-0.002" Long x .007" Max Width Through the Depth of the Countersin | 1 | |
| AFNDT-3148AL | 13 HOLE REFERENCE STANDARD, 7075-T6 ALUMINUM. HOLE SIZES: 5/32", 3/16", 7/32", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8" & 1". THRU EDM NOTCHES IN EACH HOLE, Depth: 0.040" +/- 0.001 x Width : 0.005" + 0 - 0.002". Includes Certification R... | 1 | |
| AFNDT-3153/7075T6 | 11 HOLE REFERENCE STANDARD IN 7075-T6 ALUMINUM; HOLE SIZES: (1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 3/8, 7/16, 1/2, 9/16), WITH .050"x.050" .005±.001 CORNER EDM NOTCH IN EACH HOLE. | 1 | |
| AFNDT-3158 | 3 HOLE REFERENCE STANDARD. MATERIAL: 4130 CRES STEEL. HOLE SIZES: 3/16, 1/4, 5/16 TOTAL OF 3 EDM THROUGH NOTCHES .020 DEEP x .006" WIDE. Includes Certification Report. | 1 | |
| AFNDT-3166 | CUSTOM 2 HOLE REFERENCE STANDARD. MATERIAL: 718 INCONEL, BLOCK SIZE: .500" x 1.0" x 4.0" . HOLE SIZES: 5/16", 9/32" WITH -3( .030" x .060" x .005" W MID-WALL NOTCH ' | 1 | |
| AFNDT-3167CS | CUSTOM HOLE REFERENCE STANDARD in 4130 OR 4340 STEEL; HOLE SIZES: 2 OF EACH SIZE HOLE FOR A TOTAL OF 4 HOLES. 2.5mm(.098"), ,3.5mm(.137") , WITH A .030"x.030" x .005" +/-.002" CORNER EDM NOTCH AND .020" x .005" THRU NOTCHES. | 1 | |
| AFNDT-3171AL | 17 HOLE REFERENCE STANDARD 7075-T6 1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 9/16, 5/8, 11/16 and 3/4 diameters. Includes 15 Thru EDM Notches .040" +/- 10% x .005" +/- .001" Wide. Includes Test Report and Certificate ... | 1 | |
| AFNDT-3171CS | 17 HOLE REFERENCE STANDARD 4130/4340 Carbon Steel, 1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 9/16, 5/8, 11/16 and 3/4 diameters. Includes 15 Thru EDM Notches .040" +/- 10% x .005" +/- .001" Wide. Includes Test Report ... | 1 | |
| AFNDT-3171SS | 17 HOLE REFERENCE STANDARD 304 Stainless Steel, 1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 9/16, 5/8, 11/16 and 3/4 diameters. Includes 15 Thru EDM Notches .040" +/- 10% x .005" +/- .001" Wide. Includes Test Report and... | 1 | |
| AFNDT-3180 | 6 FLAT BOTTOM HOLE REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. Hole Sizes: 5/16", 3/8", 7/16", 1/2", 9/16", 5/8" .060" LONG X. 020" x DEEP x .005" WIDE +/- .001" WIDE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3189AL | 11 HOLE REFERENCE STANDARD IN 2024-T3 ALUMINUM; HOLE SIZES: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), WITH .020" x .020" x .005" +/-.001" CORNER EDM NOTCH IN EACH HOLE. Includes Certification Report and Certificate of Conformance. | 1 | |
| AFNDT-3198TI | 10 HOLE REFERENCE STANDARD 6AL-4V Titanium.Hole Sizes: (3/16", 7/32" ,1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .030" X. 030" x.005" +/-.002" WIDE & .020" X. 020" x.005" +/-.002" WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES .500... | 1 | |
| AFNDT-3201/321SS | EDDY CURRENT SURFACE REFERENCE STANDARD, 321SS 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3204/4130 | 8 HOLE REFERENCE STANDARD IN 4130 CARBON STEEL; HOLE SIZES: (1/8, 5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2), WITH .020"x.020" CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3204/7075 | 8 HOLE REFERENCE STANDARD IN 7075-T6 ALUMINUM; HOLE SIZES: (1/8, 5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2), WITH .020"x.020" CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3210 | SURFACE REFERENCE STANDARD, ONE EDM NOTCH .030" Deep x .040" wide x .060 long ( +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 2.0"L x 2.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3212AL | 13 HOLE REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 23/32". EACH HOLE CONTAINS A CORNER EDM NOTCH 030" x .030" x Width : 0.005" +/- 0.002". Includes Certif... | 1 | |
| AFNDT-3212ST | 13 HOLE REFERENCE STANDARD. MATERIAL: 4130 or 4340 CRES STEEL. HOLE SIZES: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 23/32". EACH HOLE CONTAINS A CORNER EDM NOTCH 030" x .030" x Width : 0.005" +/- 0.002". Includes... | 1 | |
| AFNDT-3212TI | 13 HOLE REFERENCE STANDARD. MATERIAL: 6AL-4V TITANIUM. HOLE SIZES: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 23/32". EACH HOLE CONTAINS A CORNER EDM NOTCH 030" x .030" x Width : 0.005" +/- 0.002". Includes Certifi... | 1 | |
| AFNDT-3224TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020", .040", .060" (.005"W +/- .002, MAX .007"). MATERIAL: 6AL-4v TITANIUM@2.2IACS. SIZE: 1.0"W x 6.0"L x .500". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3225AL | 12 HOLE REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010"... | 1 | |
| AFNDT-3225I | 12 HOLE REFERENCE STANDARD. MATERIAL: 718 INCONEL.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", .020... | 1 | |
| AFNDT-3225S | 12 HOLE REFERENCE STANDARD. MATERIAL: 4130 or 4340 CRES STEEL. Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LON... | 1 | |
| AFNDT-3225TI | 12 HOLE REFERENCE STANDARD. MATERIAL: 6AL-4V TITANIUM.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .004" +/- .002" WIDE THROUGH EDM NOTCH IN EACH HOLE and 3 SURFACE EDM NOTCHES .750" LONG .010", ... | 1 | |
| AFNDT-3231 | Custom McDonnell Douglas Low Frequency Eddy Current reference standard, 06-20-01 Figure 9 sheets 1-4. Material: 2024-T3 or 7075-T6 Aluminum. Fasteners: (NAS1097AD6-5 & BACB30NW6K3). Includes Test Report and Certificate of Confromance. | 1 | |
| AFNDT-3231-1 | Custom McDonnell Douglas Low Frequency Eddy Current reference standard, 06-20-01 Figure 9 sheets 1-4. Material: 2024-T3 or 7075-T6 Aluminum.Fasteners: (CR3223-5 & MS21141-5). Includes Test Report and Certificate of Confromance. | 1 | |
| AFNDT-3255AL | 11 HOLE REFERENCE STANDARD in 7075-T6 Aluminum; Hole Sizes: (5/32, 3/16,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), With a .020" x .020" x .005" +/-.002" Corner EDM Notch in each hole. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3264 | Custom Reference Standard for the Boeing Lead Screw inspection, equivalent to 7903385. Material: 4150 Alloy Steel, 1.5 Outside Diameter and 1.069" Inside Diameter with 3 EDM Flaws per BSS 7048 page 2 Table 1. Includes Test Report and Certificate of Confor | 1 | |
| AFNDT-3279/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3279/Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3280 | Surface reference standard, 4340 Steel, with EDM notch depths of 0.5mm", 1.0" and 2.0mm +/-1.3mm, Notch Width: .18mm Max. Depth: +/- .03mm. Reference standard overall dImensions 25.4mm X 101.6mm X 6.4mm). Includeds .020" thick shim and Key Ring. Supplie | 1 | |
| AFNDT-3284SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm), .050"(1.27mm) (.004"W +/- .001), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. REFERENCE P/N:29A049 | 1 | |
| AFNDT-3285/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-4PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/17-7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-7PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3286 | 12 HOLE REFERENCE STANDARD 7075-T6 (Hole Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1.0", 1-1/8",) .020"x.020" and .030"x.030" x .005"W +/-.002" CORNER EDM NOTCH PER BOEING SPECIFICATION 747 PART 6 51-00-00 PAGE 8 FIGURE 3 | 1 | |
| AFNDT-3287AL | Custom multi-hole 100° countersink reference standard Material: 7075-T6 Aluminum. Hole sizes: 5/32", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2". Countersink holes opposite side. Thru hole EDM notches in each hole, .020" Deep x .005" Wide +/-.001". Includes T | 1 | |
| AFNDT-3299/4340 | 12 HOLE REFERENCE STANDARD . HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .002" WIDE MID-WALL EDM NOTCH. Material: 4340 Steel. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3299/6AL-4V | 12 HOLE REFERENCE STANDARD . HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .002" WIDE MID-WALL EDM NOTCH. Material: 6AL-4v Titanium. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3299/7075-T6 | 12 HOLE REFERENCE STANDARD . HOLE SIZES: 1/8", 5/32", 3/16", 7/32" 1/4" , 5/16", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .005" +/- .002" WIDE MID-WALL EDM NOTCH. Material: 7075-T6 Aluminum. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/MAG | EDDY CURRENT METRIC SURFACE REFERENCE STANDARD. EDM NOTCH SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: MAGNESIUM ZK60A-T5 PER ASTM-B107. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3312AL | 12 HOLE REFERENCE STANDARD, 7075-T6 Aluminum. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010" .020", .040" Tolerance: . | 1 | |
| AFNDT-3314SS | 12 HOLE REFERENCE STANDARD, 304 STAINLESS STEEL. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010", .020", .050" Tolera... | 1 | |
| AFNDT-3314TI | 12 HOLE REFERENCE STANDARD, 6AL-4V TITANIUM. HOLE SIZES: 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4" .020" x .004" +/- .001" Wide Thru EDM Notch. A Total of 4 Surface EDM Notches .005", .010", .020", .050" Tolerance: . | 1 | |
| AFNDT-3315AL | EDDY CURRENT SURFACE REFERENCE STANDARD, 4 EDM NOTCHES .005", .010", .020" and .050" x (.004"W +/- .002). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3319SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .020"(0.5mm), .040"(1.0mm), .079"(2.0mm) (.005"W +/- .002), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3320AL | 6 Hole reference standard (Aluminum 7075-T6 manufactured in accordance with Boeing Specification 51-00-02 Part 6 Procedure 1 or 2. Hole Sizes: 15/32", 17/32", 9/16", 11/16", 5/8", 3/4" ( .020" x .020" x .005" +/- .002), ( .030" x .030" x .005" +/- .002 | 1 | |
| AFNDT-3321AL | 5 Hole reference standard (Aluminum 7075-T6 manufactured in accordance with Boeing Specification 51-00-16 Part 6 Page 9 Figure 3. Hole Sizes: 11.5mm, 14.4mm, 14.6mm, 17.4mm and 17.5mm. Corner EDM Notches ( .020" x .020" x .005" +/- .002), ( .030" x .0 | 1 | |
| AFNDT-3338/17-4 | Surface reference standard, 17-4PH Steel, with EDM notch depths of 0.005", 0.010" and 0.020" inches +/-.001 (0.127mm, 0.254mm and .508mm), Notch Width: .004" +/-.001" Wide EDM notches, .005" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| AFNDT-3347CS | EDDY CURRENT WELD SURFACE REFERENCE STANDARD. EDM NOTCHES: 0.5mm, 1.0mm, 2.0mm (.1mm (.004") WIDE ± .05mm( .002") MAX WIDTH .152mm (.006"). MATERIAL: 4340 CARBON STEEL. SIZE: 1.0"W x 4.0"L Includeds 4 piece .020" thick shim and Key Ring set. Includes Tes | 1 | |
| AFNDT-3353/2024T3 | Custom 12 Hole Reference Standard. Contains hole sizes; 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8 and 3/4 inch diameters. ( .030 x .030) Corner EDM Notches and .020" mid-wall EDM Notches, 3 Surface EDM Notches .008", .020", .040" Deep | 1 | |
| AFNDT-3353/I625 | Custom 12 Hole Reference Standard. Contains hole sizes; 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8 and 3/4 inch diameters. ( .030 x .030) Corner EDM Notches and .020" mid-wall EDM Notches, 3 Surface EDM Notches .008", .020", .040" Deep | 1 | |
| AFNDT-3357/2024T4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .001), 2024-T4 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-3369/7075T6 | Custom 8 hole 100° countersink reference standard Material: 7075-T6 Aluminum. Hole sizes: 5/32", 3/16", 7/32" 1/4", 5/16", 3/8", 7/16", 1/2". Countersink holes opposite side. Thru hole EDM notches in each hole, .020" Deep x .005" Wide +/-.001". Includes | 1 | |
| AFNDT-3370/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(.76mm) (.004"W +/- .002), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3395 | CUSTOM EC SKIN INSPECTION REFERENCE STANDARD. Contains various EDM Nothes in the Upper and Lower Skin. Upper Skin Thickness of .080" and Lower Skin Thickness of .100" Thick. Standard Physical Size = 13.5" Long x 5.15" Wide. MATERIAL: 2024-T3 ALUMINUM. I | 1 | |
| AFNDT-3396CS | SURFACE NOTCH REFERENCE STANDARD 4130 or 4340 CARBON STEEL. EDM NOTCH SIZE: FULL WIDTH OF PART x .51mm(.020") DEEP +/- .05mm(.002"). BLOCK SIZE: 1.0" WIDE x 3.0" LONG. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3399S | 12 HOLE REFERENCE STANDARD 4340 STEEL.Hole Sizes: 6.35mm, 5.54mm, 4.75mm, 3.96mm, 3.18mm, 2.36mm. (1/4", 7/32", 3/16", 5/32", 1/8", 3/32"), 0.5mm x 0.5mm x 0.15mm (.0197" X .0197" x.0059")WIDE CORNER EDM NOTCH EACH HOLE and 3 SURFACE EDM NOTCHES 0.2mm, | 1 | |
| AFNDT-3421/7075T6 | 12 HOLE REFERENCE STANDARD IN 7075-T6 ALUMINUM; HOLE SIZES: (5/32, 3/16, 7/32,1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16, 3/4), WITH A .020"x.020" and .030"x.030" CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance | 1 | |
| AFNDT-3422 | Titanium(6AL-4V) Multi-hole reference standard with certificate. Contains 20 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 1.0" inch. Each hole contains two EDM c | 1 | |
| AFNDT-3425 | Custom Eddy Current Multi-Hole Reference Standard. Hole Diameters: 7.0 mm, 7.5 mm, 8.0 mm, 8.5 mm, 9.0 mm, 9.5 mm, 10.0 mm, 10.5mm, 11.0 mm, 11.5 mm, 12.0 mm, 12.5 mm, 13.0 mm, 13.5 mm, 14.0 mm. Two (2) EDM notches per hole.Material: Aluminium 7075-T76. | 1 | |
| AFNDT-3440/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3440/6AL-4V | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: 6AL-4V Titanium. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3457 | EDDY CURRENT SURFACE REFERENCE STANDARD. Cadmium plated on one side to AMS-QQ-P-416-f Type 1, Class 2. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .008", .020", .040". NOTCH WIDTH: (.004"W +/- .002). MATERIAL: 4340 STEEL. SIZE: 1. | 1 | |
| AFNDT-3470/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCH .020"(0.5mm), (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 3.0"L x .25".Includes certification Report Traceable to NIST and Certificate of Conformance(COC). | 1 | |
| AFNDT-3499 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 4 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .005", .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4... | 1 | |
| AFNDT-3500/MAG | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020", 0.030 and 0.040" inches (0.2mm, 0.51mm, 0.76mm and 1.02mm). Reference standard overall dImensions 1 X 5 X 0.25 inches (2.54cm X 12.7cm X 6.35mm). EDM notches .007" W MAX Inclu | 1 | |
| AFNDT-3504TI | 12 HOLE REFERENCE STANDARD MANUFACTURED TO SPECIFICATION USAF T.O. 33-B-1-1. MATERIAL: 6AL-4V TITANIUM. HOLE SIZES: 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/ 16" 5/8", 3/4" 0.020" x 0.004" +/-.001" Wide thru EDM NOTCHES. 4 tot... | 1 | |
| AFNDT-3506 | SINGLE HOLE REFERENCE STANDARD, HOLE SIZE 3.0", EDM CORNER NOTCH: .030" x .030" x .005 ± .002", MID-WALL NOTCH:.060" x .030" DEEP +/-.002". MATERIAL: 7075-T6 DIMENSIONS: 4.0" x 4.0" x 0.5" Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3513AL | SAFRAN MESSIER -BUGATTI-DOWTY REFERENCE STANDARD Material aluminum 7075-T6; Thickness 1/2"...- Number of holes 11;..- hole diameters: 14.0mm, 14.2mm, 14.4mm, 14.6mm, 15.6mm, 15.8mm, 16.1mm, 16.2mm, 16.3mm, 16.6mm, 16.9mm...EDM notch in each hole: thru ... | 1 | |
| AFNDT-3519SS | 6 HOLE REFERENCE STANDARD IN 304 STAINLESS STEEL; HOLE SIZES: (1/8, 5/32, 3/16, 7/32, 1/4, 9/32), WITH .030"x.030" CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3522AL | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 7075-T6 ALUMINUM. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522SS | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 304 STAINLESS STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522ST | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 4340 STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3531/2014-T6 | 13 HOLE REFERENCE STANDARD, 2014-T6 Aluminum. HOLE SIZES: 5/32", 3/16", 7/32" 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 1/2", 9/16" 5/8", 3/4", MId-Wall EDM Notch = .060"L x .030D x .004" ± .001". Manufactured in accordance to Aircraft Braking System... | 1 | |
| AFNDT-3534/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.5mm), .030"(.762mm) (.004"W +/- .002), 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3546AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHE SIZES: .005"(.127mm) , .020"(0.5mm), .050"(1.27mm) (.005"W +/- .001). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3551CS | 7 HOLE REFERENCE STANDARD in 4340 Steel; Hole Sizes: .875", 1.000", 1.100", 1.200", 1.300", 1.400", 1.500"), With a .030" x .030" x .004" ± .001" Corner EDM Notch in top and bottom of each hole in the top plate. 14 Notches Total. Includes Engraving, ... | 1 | |
| AFNDT-3559AL-3 | 15 HOLE REFERENCE STANDARD, Material: 7075-T6 Aluminum. Hole Sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1.0. A Total 15 Mid-bore notch @ 0.030" deep x 0.004" wide x 0.060" long in each hole. 3 Surface EDM No... | 1 | |
| AFNDT-3560A | Corrosion Reference Standard used for verifying function of low frequency corrosion probes. It is 0.100” thick with simulated 5%, 10% and 20% material loss. Overall size: 7.50” x 3.50” (190 x 89 mm). Material: 2024-T3 Aluminum. Includes Certification. | 1 | |
| AFNDT-3560B | Corrosion Reference Standard used for verifying function of low frequency corrosion probes. It is 0.100” thick with simulated 5%, 10% and 20% material loss. Overall size: 7.50” x 3.50” (190 x 89 mm). Material: 7075-T6 Aluminum. Includes Certification. | 1 | |
| AFNDT-7003TI | 12 HOLE REFERENCE STANDARD. MATERIAL: 6AL-4V Titanium.Hole Sizes: (3/16", 7/32" ,1/4", 9/32", 5/16",11/32", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"), .020" X .005" WIDE +/-.001" THROUGH EDM NOTCH IN EACH HOLE. Includes Test Report, Conductivity and Certi... | 1 | |
| AFNDT-CRJ200/CRS | SURFACE REFERENCE STANDARD, ALUMINUM, .005W x .008", .020", .040" EDM NOTCH DEPTHS . MATERIAL 2024-T3 AL...CRJ200 PART1 51-20-06 PG.9 | 1 | |
| AFNDT-VL769-1A | TITANIUM VERTICAL(INBOARD LUG) ULTRASONIC REFERENCE STANDARD(.800"THICK, 3.56" OUTSIDE RADIUS WITH A 1.312" BORE DIAMETER. COPPER BERYLLIUM NON FLANGED BUSHING WITH A 1.128 BORE DIA. ( 2 EACH .100" x .100" CORNER NOTCHES) | 1 | |
| AFNDT-VL769-2A | TITANIUM VERTICAL(INBOARD LUG) ULTRASONIC REFERENCE STANDARD(1.500" THICK, 3.56" OUTSIDE RADIUS WITH A 1.312" BORE DIAMETER. COPPER BERYLLIUM NON FLANGED BUSHING WITH A 1.128 BORE DIA. ( 2 EACH .100" x .100" CORNER NOTCHES) | 1 | |
| AFS-0506 | 5MHZ 51° SHEAR WAVE IN ALUMINUM. CASE SIZE .50" W x .80"L x .37"H, REFERENCE STANDARD NDT624 | 1 | |
| AFS-0507 | 5MHZ 32° SHEARWAVE IN ALUMINUM. CASE SIZE .50"X.80"L. HEIGHT TAPERS FROM .20"H FRONT TO .32" H BACK. REFERENCE STANDARD IS NDT624 | 1 | |
| AFS-1175 | 70°. ANGLE BEAM TRANSDUCER in ALUMINUM, SIDE MOUNT MICRODOT CONNECTOR, .187" x .187" ELEMENT. CASE SIZE: .67'L x .26"W x .33"H. Includes Test Report and Certificate of Conformance. Reference: B767 Part 4 53-50-05. Standard Part number NDT679 | 1 | |
| AFS-1175T | 70°. ANGLE BEAM TRANSDUCER in ALUMINUM, .187" x .187" ELEMENT, TOP MOUNTED MICRODOT CONNECTOR. CASE SIZE: .67'L x .26"W x .33"H. Includes Test Report and Certificate of Conformance. Reference: B767 Part 4 53-50-05. Standard Part number NDT679 | 1 | |
| AFS-1346 | CUSTOM 2 ELEMENT RING TRANSDUCER FOR BORE HOLE INSPECTION WITH BOEING REFERENCE STANDARD 55-10-13 PAGE 9 FIGURE 2. TWO MICRODOT CONNECTORS "A" and "B" | 1 | |
| AFS-1394 | CARGOLUX CUSTOM 5MHz .187", 40° IN ALUMINUM SHEAR WAVE TRANSDUCER WITH A 1.00" RADIUS FOR THE BOEING REFERENCE STANDARD LUG 1B7- FITTING-SEQUENCE CARRIAGE ATTACHMENT INBOARD TRAILING EDGE FLAP. CASE SIZE: .500"L x .270"W x .350". Includes Test Report... | 1 | |
| AFS-5825 | Custom 5MHz 22° shear wave transducer .375" element. 1.90"(51mm) radius. Case Size: .75"L x .50"W x .25"H. Used with reference standard NDT3195. | 1 | |
| AFS-5826 | Custpm 5MHz 31° shear wave transducer .375" element. 2.0"(51mm) radius. Case Size: ..75"L x .50"W x .25"H end mounted microdot connector. Used with reference standard NDT3196. | 1 | |
| AFS-5827 | Custpm 5MHz 33° shear wave transducer .375" element. 2.0"(51mm) radius. Case Size: ..75"L x .50"W x .25"H end mounted microdot connector. Used with reference standard NDT3197. | 1 | |
| AFS-5828 | Custpm 5MHz 26° shear wave transducer .375" element. 2.0"(51mm) radius. Case Size: ..75"L x .50"W x .25"H end mounted microdot connector. Used with reference standard NDT3197. | 1 | |
| AFW-45/1.83R | 45° IN ALUMINUM LUCITE (PLEXIGLASS) WEDGE, 3/8-32 THREAD WITH A 1.83" RADIUS USED WITH A .25"Ø DIAMETER TRANSDUCER AFC-0520(ABT-0504). Includes Certificate of Conformance...Used with Fairchild Reference Standard part number 27-95031-001. | 1 | |
| AGE-02321-401 | Embraer 170 Reference Standard. Material: 2024-T351 Clad. Top skin = 0.040, Lower skin = 0.080. Rivet - MS2047AD-5. Includes Test Report and Certificate of Conformance. | 1 | |
| AGE-04383-003 | REFERENCE STANDARD FOR WINDSHIELD POST | 1 | |
| AHS29-1A-0 | (Aluminum Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/32", 7/... | 1 | |
| AHS29-1A-2 | (Aluminum Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/32", 7/... | 1 | |
| AHS29-1S-0 | Carbon Steel(4340) Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 2... | 1 | |
| AHS29-1SS-0 | (304 Stainless Steel Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16",... | 1 | |
| AHS29-1SS-1 | (Stainless Steel Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/… | 1 | |
| AHS29-1T-0 | Titanium(6AL-4V) Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/... | 1 | |
| AHS29-C2-A1 | CUSTOM 29 HOLE REFERENCE STANDARD 7075-T6 ALUMINUM WITH 0.015" THRU EDM NOTCH AND 0.030X0.030 CORNER NOTCH. Includes Test Report Traceable to NIST and Certificate of Conformance. | 1 | |
| AHS29-C30304 | 304 Stainless Steel Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/ | 1 | |
| AHS29-C30INC | Inconel 718 Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/32", 7/8 | 1 | |
| AHS29-C30TI | 6AL-4V Titanium Multi-hole reference standard with certificate. Contains 29 holes; 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2", 17/32", 9/16", 19/32", 5/8", 21/32", 11/16", 23/32", 3/4", 25/32", 13/16", 27/32", | 1 | |
| AL29-32 | CALIBRATION REFERENCE STANDARD, BLOCK, 2024-T3 ALUMINUM ALLOY, CONDUCTIVITY BETWEEN 29% AND 32% IACS, CONTAINS 0.008 IN. (0.20 MM), 0.020 IN. (0.51 MM), AND 0.040 IN. (1.02 MM) DEEP SURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES, (MHIRJ OR EQUIVALENT) | 6 | |
| AL35-45 | BOMBARDIER SURFACE REFERENCE STANDARD - 7075-T7ALUMINUM. FULL WIDTH EDM NOTCHES .008", .020", .040" (.005"W +/- .002, MAX.006) BLOCK SIZE: 3.75"L x 1.50"W x 0.25"H | 8 | |
| AMP-39-B-53-10-00-00A-31BA-K | REFERENCE STANDARD PER AW139 IETP 33rd Issue. Material: AISI 301-1/4 HARD STEEL, 7075 AL | 1 | |
| AMS2630C Custom | Custom Reference Standard Per SAE AMS2630C. material: Titanium Alloy, Ti6Al4V per AMS-4928R Annealed. Includes 2 EDM Flaws per customer supplied Drawing. Includes Test Report Traceable to NIST and Certificate of Conformance. | 1 | |
| AN670-55-31-102 | CALIBRATION REFERENCE STANDARD (CRS), MADE OF ALUMINUM WITH MULTIPLE LAYERS CONTAINING ELECTRICAL DISCHARGE MACHINED (EDM) NOTCHES (MHIRJ) | 1 | |
| APB-NDT001 | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-02 Page 6 Frigure 2. Material: 7150-T6 (34-39.5% IACS), 7050-T7 (40-44% IACS), and 2324-T3 (29.5-33.5% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes | 1 | |
| APB-NDT003 | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-02 Page 9-10 Figure 5. Material: 7150-T6 (34-39.5% IACS), 7050-T7 (40-44% IACS), and 2324-T3 (29.5-33.5% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Include | 1 | |
| APB-NDT004 | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-01 Page 5-6 Figure 2. Material: 7150-T6 (34-39.5% IACS), 7050-T7 (40-44% IACS), and 2324-T3 (29.5-33.5% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Include | 1 | |
| APB-NDT005 | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-02 Page 13-14. Figure 7. Material: 7150-T6 (34-39.5% IACS), 7050-T7 (40-44% IACS), and 2324-T3 (29.5-33.5% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Inclu | 1 | |
| APB-NDT006 | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-53 Page 5-6 Figure 2. Material: 7075-T7 (40-44% IACS), 2324-T3 (29.5-33.5% IACS), and 2224-T3 (29.5-33.5% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Inclu | 2 | |
| APB-NDT011A | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-08 Page 8-9 Figure 3. Material: 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT011B | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-08 Page 11-12 Figure 5. Material: 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT011C | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-08 Page 14-15 Figure 7. Material: 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT011D | AVIATION PARTNERS BOEING REFERENCE STANDARD 767 Part 6 57-20-08 Page 17-18 Figure 9. Material: 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT015 | BOEING AVIATION PARTNERS REFERENCE STANDARD 767 Part 6 57-20-09 Page 21-22 Figure 10. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Ce | 1 | |
| APB-NDT016 | BOEING AVIATION PARTNERS REFERENCE STANDARD 767 Part 6 57-50-09 Page 24-25. Figure 12 Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Ce | 1 | |
| APB-NDT3301 | AVIATION PARTNERS BOEING REFERENCE STANDARD 737 Part 6 57-20-34 Page 7-8 Figure 2. Material: 2024-T3 (28.5-32% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT5203 | AVIATION PARTNERS REFERENCE STANDARD 737 Part 6 57-20-02 Page 7-8 Figure 2. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate | 2 | |
| APB-NDT5204 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-02 Page 11-12 Figure 4. Material: 2224-T3 and 2324-T3 or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 2 | |
| APB-NDT5205 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-02 Page 15-16 Figure 6. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Cer | 2 | |
| APB-NDT5206 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-03 Page 8-9 Figure 2. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certi | 2 | |
| APB-NDT5207 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-03 Page 12-13 Figure 4. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Cer | 2 | |
| APB-NDT5208 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-03 Page 16-17 Figure 6. Material: 2224-T3 (29.5-33.5% IACS) and 2324-T3 (29.5-33.5% IACS), or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Cer | 2 | |
| APB-NDT5301 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-01 Page 15-16 Figure 6. Material: 7050-T7 (40-44% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT5302 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-01 Page 11-12 Figure 4. Material: 7050-T7 (40-44% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| APB-NDT5303 | AVIATION PARTNERS BOEING REFERENCE STANDARD 757 Part 6 57-20-01 Page 7-8 Figure 2. Material: 7050-T7 (40-44% IACS) or Airplane Quality Material with an Electrical Conductivity Between ±5%. Includes Test Report and Certificate of Conformance. | 1 | |
| ARP-.385/.720 | LOW FREQUENCY REFLECTION RING PROBE, 500Hz-5KHz.385"Ø ID .720"Ø OD, SUPPLIED WITH A TRIAX FISCHER CONNECTOR. FOR REFERENCE STANDARD APB-3302. Includes Test Report and Certificate of Conformance. | 1 | |
| ARP-.85/1.40-200Hz | LOW FREQUENCY REFLECTION RING PROBE .85" I.D. 1.40" O.D. TRIAX CONNECTOR 100Hz-500Hz. REFERENCE STANDARD NDT3176-X 737 PT 6 57-10-59. Includes test report and Certificate of Conformance. | 1 | |
| ARP-1.2/100H-7 | LOW FREQUENCY REFLECTION RING PROBE 1.2" OD, .605" ID, 50Hz-3KHz TRIAX FISHER CONNECTOR. 737 PART 6 57-10-58, pg.2. and 737 PART 6 57-10-54, pg.2 USED WITH NDT3153-X AND 3167-X SERIES REFERENCE STANDARDS. Includes Test Report and Certificate of ... | 1 | |
| ARP-1.25-.75-300H | REFLECTION RING PROBE TRIAX FISHER CONNECTOR, 1.25"OD .75" ID(19.6mm) 300HZ-1KHZ. 737 PART 6 57-10-53, pg.2, USED WITH REFERENCE STANDARD NDT3168 AND NDT3176-X. Includes test report and Certificate of Conformance... | 1 | |
| ARP-1.40/.85-200Hz | LOW FREQUENCY REFLECTION RING PROBE .85" I.D. 1.40" O.D. TRIAX FISCHER CONNECTOR 100Hz-500Hz. REFERENCE STANDARD NDT3176-X 737 PT 6 57-10-59. Includes test report and Certificate of Conformance. | 1 | |
| ARS-0812S | Surface reference standard, 17-4PH Steel, with EDM notch depths of 0.008", 0.010" and 0.020" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inc | 1 | |
| ARS-0824-7050 | Surface reference standard, 7050-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824-7050T74 | Surface reference standard, 7050-T74 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824-7075T6 | Surface reference standard, 7075-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824-7075T7 | Surface reference standard, 7075-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824-7075T73 | Surface reference standard, 7075-T73 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/2024-T3 | Surface reference standard, 2024-T3 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824/2024-T6 | Surface reference standard, 2024-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/2024T6 | Surface reference standard, 2024-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .004" +/-.002" Wide EDM notches, .006" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 | 1 | |
| ARS-0824/4330 | Surface reference standard, 4330 Steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inches | 1 | |
| ARS-0824/6061T6 | Surface reference standard, 6061-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824/7475-T7 | Surface reference standard, 7475-T7 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824A | Surface reference standard, 7075-T6 Aluminum, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.... | 1 | |
| ARS-0824I | Surface reference standard, Inconel 718, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824M | Surface reference standard, Magnesium, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM notches .007" W MAX | 1 | |
| ARS-0824S | Surface reference standard, 4340 Steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.25 inc... | 1 | |
| ARS-0824SS | Surface reference standard, 304 Stainless steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM NOTCHES .005" W +/-.001" | 1 | |
| ARS-0824SS/316 | Surface reference standard, 316 Stainless steel, with EDM notch depths of 0.008", 0.020" and 0.040" inches (0.2mm, 0.51mm and 1.02mm). Reference standard overall dImensions 1 X 4 X 0.25 inches (2.54cm X 10.1cm X 6.35mm). EDM NOTCHES .005" W +/-.001" | 1 | |
| ARS-0824T | Surface reference standard, 6AL-4v Titanium, with EDM notch depths of 0.008", 0.020" and 0.040" inches +/-.001 (0.2mm, 0.51mm and 1.02mm), Notch Width: .005" +/-.002" Wide EDM notches, .007" Wide MAX. Reference standard overall dImensions 1 X 4 X 0.2... | 1 | |
| ARS-1012HCS | 12 HOLE REFERENCE STANDARD 4130 OR 4340 CARBON STEEL WITH 0.020" x 0.020" and 0.030" x 0.030" CORNER EDM NOTCH. HOLE SIZES: 1/8, 5/32, 3/16, 13/64, 7/32, 5/64, 1/4, 17/64, 9/32, 19/64, 5/16, 21/64. Includes Test Report and Certificate of Conformance. | 1 | |
| ARS-1012HSA | 12 HOLE REFERENCE STANDARD 7075-T6 WITH 0.020" x 0.020" and 0.030" x 0.030" CORNER EDM NOTCH. HOLE SIZES: 1/8, 5/32, 3/16, 13/64, 7/32, 5/64, 1/4, 17/64, 9/32, 19/64, 5/16, 21/64. Includes Test Report and Certificate of Conformance. | 1 | |
| ARS-123/TI | EDDY CURRENT SURFACE REFERENCE STANDARD. MATERIAL: TI-6AL-6V-2SN. SIZE: 2.0" LONG x 1.0" WIDE. EDM NOTCH .040" DEEP +/- .002" x .005" WIDE +/- .001". Includes Test Report and Certificate of Conformance. | 1 | |
| ARS-1S | Surface reference standard, 4340 or 4130 steel, with EDM notch depth of 0.010" x .005" wide Reference standard overall dImensions 1.0" X 3.0" X 0.25" inches .007" W MAX. Includes Certification traceable to NIST. | 1 | |
| BH7475-T7351 | CALIBRATION REFERENCE STANDARD, ALUMINUM ALLOY, CONDUCTIVITY VALUE OF 35% TO 45% IACS THAT CONTAINS VARIOUS HOLE SIZES WITH 0.040 IN. (1.02 MM) DEEP ELECTRICAL DISCHARGE MACHINED NOTCHES, (MHIRJ OR EQUIVALENT) | 4 | |
| BHS6061-T6/C2 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | 1 | |
| CA12-1508A | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 7075-T7 ALUMINUM, 54-10-11 PAGE 634A FIG.603 SHEET 21B | 1 | |
| CA12-1683A | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 STEEL, 54-10-11 PAGE 632C FIG.603 SHEET 20C | 1 | |
| CE9900088-001 | COMPOSITE SANDWICH CALIBRATION REFERENCE STANDARD | 1 | |
| CE9900088-003 | COMPOSITE SANDWICH CALIBRATION REFERENCE STANDARD | 1 | |
| CE9900088-007 | COMPOSITE SANDWICH CALIBRATION REFERENCE STANDARD | 1 | |
| CE9900088-009 | COMPOSITE SANDWICH CALIBRATION REFERENCE STANDARD | 1 | |
| CE9900430-001 | COMPOSITE SANDWICH CALIBRATION REFERENCE STANDARD | 1 | |
| DC-10 FIG603/15C | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 628B FIG.603 SHEET 15C | 1 | |
| DC-10 FIG603/15E/4340 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 CARBON STEEL, 54-10-11 PAGE 628D FIG.603 SHEET 15E | 1 | |
| DC-10 FIG603/15E/Ti | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 628D FIG.603 SHEET 15E | 1 | |
| DC-10 FIG603/15G | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 CARBON STEEL, 54-10-11 PAGE 628F FIG.603 SHEET 15G | 1 | |
| DC-10 FIG603/23 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 7075-T6 ALUMINUM, 54-10-11 PAGE 635 FIG.603 SHEET 23 | 1 | |
| DC-10 FIG603/24-Al | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 636C FIG.603 SHEET 24 | 1 | |
| DC-10 FIG603/24-Ti | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 636C FIG.603 SHEET 24 | 1 | |
| DC-10 FIG603/25 | DOUGLAS DC-10 WING CLEVIS REFERENCE STANDARD 6AL-6V or 6AL-4 TITANIUM, 54-10-11 PAGE 637 FIG.603 SHEET 25 | 1 | |
| DC-10 FIG603/27Al | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 639 FIG.603 SHEET 27 | 1 | |
| DC-10 FIG603/27Ti | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 639 FIG.603 SHEET 27 | 1 | |
| DC-10 FIG603/28LOWER/Al | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 640 FIG.603 SHEET 28 (LOWER) | 1 | |
| DC-10 FIG603/28LOWERTi | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 640 FIG.603 SHEET 28 (LOWER) | 1 | |
| DC-10 FIG603/28UPPER/Al | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 640 FIG.603 SHEET 28 (UPPER) | 1 | |
| DC-10 FIG603/28UPPER/Ti | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 640 FIG.603 SHEET 28 (UPPER) | 1 | |
| DC-10 FIG603/29Al | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 641 FIG.603 SHEET 29 | 1 | |
| DC-10 FIG603/29Ti | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 6AL-4V TITANIUM, 54-10-11 PAGE 641 FIG.603 SHEET 29 | 1 | |
| DC-10 FIG603/30-AL | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 7075-T6 ALUMINUM, 54-10-11 PAGE 642 FIG.603 SHEET 30 | 1 | |
| DC-10 FIG603/39-1 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4130 or 4340, 54-10-11 PAGE 651 FIG.603 SHEET 39, BOLT IDENTIFICATION 71658-7-35 #1 | 1 | |
| DC-10 FIG603/39-2 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4130 or 4340, 54-10-11 PAGE 651 FIG.603 SHEET 39, BOLT IDENTIFICATION 71658-18-53 #2 | 1 | |
| DC-10 FIG603/39-3 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4130 or 4340, 54-10-11 PAGE 651 FIG.603 SHEET 39, BOLT IDENTIFICATION 71658-18-53 #3 | 1 | |
| DC-10 FIG603/39-4 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4130 or 4340, 54-10-11 PAGE 651 FIG.603 SHEET 39, BOLT IDENTIFICATION 71658-7-35 #4 | 1 | |
| DC-10 FIG603/43 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 2024-T351 ALUMINUM, 54-10-11 PAGE 655 FIG.603 SHEET 43 | 1 | |
| DC-10 FIG603/5 | DOUGLAS DC-10 WING PYLON REFERENCE STANDARD 4340 CARBON STEEL, 54-10-11 PAGE 617 FIG.603 SHEET 5 | 1 | |
| DHC-29444 | Q400 Reference Standard, De Havilland Drawing No DHC29444-01 | 1 | |
| DHC-29444-001 | Q400 Reference Standard, De Havilland Drawing No DHC29444-001 | 1 | |
| DRT74469 | Messier-Dowty Reference Standard, Aluminum, Appendix A Service Bulletin No. 146-32-174 Pg 4 Fg A2 | 2 | |
| EDM NOTCH(0.030INCH DEEP,0.005 INCH WIDE,0.060 INCH LONG ) IN DIRECTION OF CIRCUMFERENCE | ALUMINIUM REFERENCE STANDARD(USED FOR WHEEL GOODRICH PART NO. 3-1423-1,-2 ) | 1 | |
| ET.28 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | 1 | |
| EXBC670-59066−001 | CALIBRATION REFERENCE STANDARD CONTAINS 0.250 IN (6.35 MM) LONG0.005 IN. (0.127 MM) WIDE ELECTRICAL DISCHARGE MACHINED NOTCHES (BOMBARDIER INC.) | 1 | |
| EXBC670−59066−001 | Calibration reference standard contains 0.250 in (6.35 mm) long0.005 in. (0.127 mm) wide electrical discharge machined notches (Bombardier Inc.) | 1 | |
| EXSH690-31022 | CALIBRATION REFERENCE STANDARD POTABLE WATER. | 1 | |
| EXSH690−31022 | Calibration reference standard potable water. | 1 | |
| F15-AL-UT-0.175-2 | F15 REFERENCE STANDARD. MATERIAL: 2024-T3, OUTBOARD TORQUE BOX REAR SPAR, 68A115101, LOWER FLANGE FASTENER HOLES. Includes Test Report and Certificate of Conformance. | 1 | |
| FF171-5234 | BOEING REFERENCE STANDARD. MATERIAL: 6AL-4V TITANIUM ROUND 2.50" DIAMETER O.D. / 1.125" DIAMETER I.D. EDM CORNER NOTCH: .030" x .030" +0.00/-0.002 WIDE | 1 | |
| GENERAL BLOCK 29A032 | TITANIUM REFERENCE STANDARD 3 EDM CUT DEPTH 0.2 MM, 0.5 MM AND 1MM WITH WIDTH 0.05 MM – 0.25 MM | 1 | |
| GENERAL BLOCK 29A49 | STEEL REFERENCE STANDARD 3 EDM CUT DEPTH 0.2 MM, 0.5 MM AND 1MM WITH WIDTH 0.05 MM – 0.25 MM | 1 | |
| KC10RS.15C | KC10 Reference Standard, KC10 W7 PG1 SHEET1 | 1 | |
| KC10RS.15a | KC10 Reference Standard, KC10 W23 PG1 SHEET1 | 1 | |
| KC10RS.15b | KC10 Reference Standard, KC10 W23/W7 PG1 SHEET1 | 1 | |
| KC10RS.51-1 | KC10 Reference Standard, KC10 W31 PG1 SHEET1 | 1 | |
| KT56778 | MESSIER-DOWTY REFERENCE STANDARD 631-32-181 2024-T3 | 1 | |
| Lucite Wedge 120P | Custom Lucite Wedge for Reference Standard 1. Material: Lucite/Cast Acrylic | 1 | |
| M346 SPAR 4 STD-1 | CUSTOM REFERENCE STANDARD, H346 SPAR 4 STD-1 HOLE INTERFACE WITH FLAPS HINGE REWORK. MATERIAL: 7050-T7451 ALUMINUM. Includes Test Report and Certificate of Conformance. | 1 | |
| MHS-12-1A-2 | ALUMINUM (7075-T6) MULTI-HOLE REFERENCE STANDARD WITH CERTIFICATE TRACEABLE TO NIST | 1 | |
| MHS-29-1A-0 | REFERENCE STANDARD, 29 HOLES 1/8" THRU 1" IN 1/32" INCREMENTS WITH .030" CORNER NOTCH PLUS .010, .02 | 1 | |
| NDT 194B | Boeing Reference standard w/Certs | 2 | |
| NDT 6001 | Boeing Steel Reference Standard w/certs | 2 | |
| NDT 6018 | Boeing Titanium Reference Standard w/certs | 2 | |
| NDT-1094-110-A | BOEING REFERENCE STANDARD 737 PART 4 53-30-07, 757 PART 4 53-00-02 FIG 2, 777 PART 4 53-00-02 PAGE 34 FIGURE 2. MATERIAL: ALUMINUM. PROCUDURES VARY WITH PLANE MODEL. ALL MODELS FOR THIS REFERENCE STANDARD. INCLUDES TEST REPORT AND CERTIFICATE OF CONFORMAN | 2 | |
| NDT-1094-130-A | BOEING REFERENCE STANDARD 737 PART 4 53-30-07, 757 PART 4 53-00-02 FIG 2, 777 PART 4 53-00-02 PAGE 34 FIGURE 2. MATERIAL: ALUMINUM. PROCUDURES VARY WITH PLANE MODEL. ALL MODELS FOR THIS REFERENCE STANDARD. INCLUDES TEST REPORT AND CERTIFICATE OF CONFORMAN | 2 | |
| NDT1022-27/6 | BOEING REFERENCE STANDARD 767 51-00-14 PT 6 FIG 3, 757 Part 6 51-00-14 Page 8 Figure 3. SINGLE STANDARD WITH ALL SIX HOLES. MATERIAL(6AL-4V) TITANIUM. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT1033-10 | ALUMINUM TO ALUMINUM SKIN REFERENCE STANDARD WITH A TOTAL OF 10 BONDED SHIMS .016"-.125" THICK. 100 THICKNESS COMBINATIONS WITH SIMULATED DISBOND DEFECTS. PART 4 51-00-01 | 4 | |
| NDT1047 | BOEING 737 REFERENCE STANDARD PART 6 51-00-00 PAGE 5 FIGURE 1. MATERIAL: LOW ALLOY 4000 SERIES STEEL 4130. Includes Test Report and Certificate of Conformance. | 3 | |
| NDT1048 | BOEING REFERENCE STANDARD W/CERTS | 4 | |
| NDT1083 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT1083-.157 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-.5625 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-.630 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.5620 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.563 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.625 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.630 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.688 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.695 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.750 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 2 | |
| NDT1083-0.787 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.812 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.813 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.875 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-0.938 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-1.000 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-1.286 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1083-1.347 | BOEING REFERENCE STANDARD 757 Part 6 51-00-17 Page 7 Figure 3. Material: Low Alloy Steel, Such as,4330 or 4340. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom Hole Size and Procedure. Includes Test Report and Cert | 1 | |
| NDT1084 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-.096 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-.5625 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.09375 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.122 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.125 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.127 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.129 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.156 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-0.157 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.161 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.200 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.218 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.219 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-0.234 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.265 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.281 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.297 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.328 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.359 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.391 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.422 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.453 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.469 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.484 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.531 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.562 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.563 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.578 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.594 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.600 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.625 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-0.630 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.640 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.656 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.675 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.688 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.689 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.695 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.700 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.719 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.750 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-0.787 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.813 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.875 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.906 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.938 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0.XXX | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-0125 | BOEING REFERENCE STANDARD 737 PART 6 51-00-00 PAGE 9 FIGURE 3, 777 PART 6 51-00-02 PAGE 7 FIGURE 3,777-200/300 PART 6 51-00-02 PAGE 9 FIGURE 3. MATERIAL: 2024-T3. PROCUDURES VARY WITH PLANE MODEL. ALL MODELS FOR THIS REFERENCE STANDARD. PROVIDE CUSTOM | 1 | |
| NDT1084-1.000 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.062 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.100 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.124 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.125 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-1.187 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.200 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.250 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.300 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.312 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.3605 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.375 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-1.400 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.437 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.500 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.625 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 2 | |
| NDT1084-1.750 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.875 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.940 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-1.9855 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-11.5MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-14.4MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-14.6MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-17.4MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-17.5MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-2.000 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-2.250 | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1084-27.6MM | BOEING REFERENCE STANDARD 737 Part 6 51-00-00 Page 9 Figure 3, 777 Part 6 51-00-02 Page 7 Figure 3, or 777-200/300 Part 6 51-00-02 Page 9 Figure 3. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Provide Custom | 1 | |
| NDT1087-11 | BOEING REFERENCE STANDARD, 757 Part 6 53-00-11. Plate Thickness: Upper 1 - 0.140 / Lower 2 - 0.080. Material: 2024-T3. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT1087-12 | BOEING REFERENCE STANDARD, 757 Part 6 53-00-11. Plate Thickness: Upper 1 - 0.120 / Lower 2 - 0.063. Material: 2024-T3. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT1087-13 | BOEING REFERENCE STANDARD, 757 Part 6 53-00-11. Plate Thickness: Upper 1 - 0.140 / Lower 2 - 0.063. Material: 2024-T3. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT1087-14 | BOEING REFERENCE STANDARD, 757 Part 6 53-00-11. Plate Thickness: Upper 1 - 0.160 / Lower 2 - 0.100. Material: 2024-T3. Includes Test Report and Certificate of Conformance. | 3 | |
| NDT1087-P1 | PROBE GUIDE USED WITH NDT1087 SERIES REFERENCE STANDARDS. BOEING 737 PART 6 53-30-00 and 777 PART 6 53-00-09 PAGE 9 FIGURE 3 | 3 | |
| NDT1088-036X2/050-B | Boeing Reference Standard, Bare, Drawing Provided | 1 | |
| NDT1088-036X2/050-C | Boeing Reference Standard, Drawing Provided | 1 | |
| NDT1088-050/063 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1088-062/071 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1088-072/050 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 4 | |
| NDT1088-095/071 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1088-112/100 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 2 | |
| NDT1088-133/071 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1088-144/050 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 3 | |
| NDT1088-156/100 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1088-180/180 | BOEING REFERENCE STANDARD 737 Part 6 53-30-24 Page 6 Figure 2, 747 Part 6 53-30-17 Page 7 Figure 1, 757 Part 6 53-00-13 Page 6 Figure 2. Material: 2024-T3. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and | 1 | |
| NDT1094-040 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-040-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-050 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-050-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-050/010-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-070 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-070-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-090 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-090-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-110 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-110-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-130 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-130-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-155 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-155-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-185 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-185-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-215 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-215-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-245 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-245-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-275 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-275-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 2 | |
| NDT1094-300 | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1094-300-A | BOEING REFERENCE STANDARD 737 Part 4 53-30-07, 757 Part 4 53-00-02 FIG 2, 777 Part 4 53-00-02 Page 34 Figure 2. Material: Aluminum. Procudures vary with Plane Model. All Models for this Reference Standard. Includes Test Report and Certificate of Conforman | 1 | |
| NDT1099G-P1 | BEOING REFERENCE STANDARD 757 Part 4 53-30-04 Page 15-17 Figure 3. Material: Delrin. *** SEE FINALIZED DRAWING*** | 1 | |
| NDT1106 | ONEYCOMB SANDWICH REFERENCE STANDARD (MAX SKIN THICKNESS OF 0.050 INCHES – 1.27MM) | 2 | |
| NDT1106-1 | Boeing Reference Standard composite..737 PT4 51-00-05 PG 5-6 FG 1 With top plate thickness of .060", .080" .100".. | 1 | |
| NDT3038P1 | Reference Standard, 737 PART4 57-50-02 **SEE NEW DRAWING** (DM) | 3 | |
| NDT3050 | BOEING REFERENCE STANDARD PT 6 53-30-20 FIG 2. Includes Test Report and Certificate of Conformance. (SCREW AND NUT) | 4 | |
| NDT3202-A | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3202-B | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3202-C | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3202-D | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3202-E | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT3202-F | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3202-G | BOEING REFERENCE STANDARD 737 Part 6 55-10-53 Page 9 Figure 2. Material: 2024-T3 or Equivalent with a Conductivity of 28-32 IACS. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT3226 | BOEING REFERENCE STANDARD 53-11-39 PART 6. MATERIAL: 2024-T3 ALUMINUM. 2. Includes Test Report and Certificate of Conformance.BACR15FT6D RIVETS BUCKED BETWEEN .250"Ø and .280"Ø. | 2 | |
| NDT3276 | BOEING REFERENCE STANDARD 737 PART 4 53-20-02 FIGURE 2 PAGE 9. MATERIAL: 2024-T3 ALUMINUM WITH RUBBER FEET ON BOTTOM FOR SUPPORT. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT3276A | BOEING REFERENCE STANDARD 737 PART 4 53-20-02 FIGURE 3 PAGE 10. MATERIAL: 2024-T3 ALUMINUM WITH RUBBER FEET ON BOTTOM FOR SUPPORT. Includes Test Report and Certificate of Conformance. . | 2 | |
| NDT396-36/36 | Boeing Reference Standard, 737 PT6 53-30-44, PG7 FIG 2, .036" Upper skin, .036 Lower skin | 1 | |
| NDT396-40/40 | Boeing Reference Standard, 737 PT6 53-30-44, PG7 FIG 2, .040" Upper skin, .040 Lower skin | 1 | |
| NDT396-45/40 | Boeing Reference Standard, 737 PT6 53-30-44, PG7 FIG 2, .045" Upper skin, .040 Lower skin | 1 | |
| NDT396-50/40 | Boeing Reference Standard, 737 PT6 53-30-44, PG7 FIG 2, .050" Upper skin, .040 Lower skin | 1 | |
| NDT396-56/40 | Boeing Reference Standard, 737 PT6 53-30-44, PG7 FIG 2, .056" Upper skin, .040 Lower skin | 1 | |
| NDT4243 | BOEING REFERENCE STANDARD 747 Part 6 57-10-31 Page 4 Figure 1. Material: 2024-T3 or An Airplane Quality with an Electrical Conductivity of 28-43% IACS. Fasteners: Non-Magetic Fastener. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6007 | Boeing Titanium Reference Standard w/certs 767 PT4 57-50-11 PG 7 FG 2 | 2 | |
| NDT6008 | Boeing Titanium Reference Standard w/certs 767 PT4 57-50-11 PG 8 FG 3 | 2 | |
| NDT6017 | Boeing Titanium Reference Standard w/certs 767 PT4 57-50-22 PG 6-7 FG 2 | 2 | |
| NDT6018 | Boeing Titanium Reference Standard w/certs 767 PT4 57-50-22 PG 8-9 FG 3 | 2 | |
| NDT6025-1 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6025-2 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6025-3 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6025-4 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6025-5 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT6025-6 | BOEING REFERENCE STANDARD 767 PART 4 57-50-17 FIGURE 2 PAGE 6. MATERIAL MUST BE MANUFACTURE OUT OF 7075-T6 PLATE WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT6045-SC1 | Boeing Transducer Guide. Material: Delrin ( Black Acetal). Used with NDT6045 Reference Standard. 767 PART 4 54-50-08 PAGE 15 FIGURE 3 | 1 | |
| NDT6045-SC2 | Boeing Transducer Guide. Material: Delrin ( Black Acetal). Used with NDT6045 Reference Standard. 767 PART 4 54-50-08 PAGE 15 FIGURE 3 | 1 | |
| NDT6052 | BOEING REFERENCE STANDARD 767 P4, 57-50-27. UT INSPECTION OF MAIN LANDING GEAR FORWARD TRUNNION SUPPORT SIDE LOAD FITTING | 1 | |
| NDT6076 | BOEING REFERENCE STANDARD 767 ..P6 57-20-10 MATERIAL: 7075-T6 OR 2024-T3 ALUMINUM. EXTERNAL LFEC INSPECTION ON STRINGERS6,10,15 AT THE LOWER WING SKIN AT RIBS3, 5, 18 AND 31. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6077 | BOEING REFERENCE STANDARD 767 ..P6 57-20-10 MATERIAL: 7075-T6 OR 2024-T3 ALUMINUM. EXTERNAL LFEC INSPECTION ON STRINGERS6,10,15 AT THE LOWER WING SKIN AT RIBS3, 5, 18 AND 31. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6078 | BOEING REFERENCE STANDARD 767 ..P6 57-20-10 MATERIAL: 7075-T6 OR 2024-T3 ALUMINUM. EXTERNAL LFEC INSPECTION ON STRINGERS6,10,15 AT THE LOWER WING SKIN AT RIBS3, 5, 18 AND 31. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6079 | BOEING REFERENCE STANDARD 767 ..P6 57-20-10 MATERIAL: 7075-T6 OR 2024-T3 ALUMINUM. EXTERNAL LFEC INSPECTION ON STRINGERS6,10,15 AT THE LOWER WING SKIN AT RIBS3, 5, 18 AND 31. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT6096 | BOEING REFERENCE STANDARD 767 PART 4 53-60-02 FIGURE 2 PAGE 6. MATERIAL: 2024-T3 ALUMINUM WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT629 | BOEING COMPOSITE REFERENCE STANDARD 767 PT 4 57-40-01. AULUMINUM to ALUMINUM HONEYCOMB CORE. Includes C-Scan Report and Certificate of Conformance. 2 year Unconditional Warranty. | 2 | |
| NDT676 | BOEING REFERENCE STANDARD FOR PW4000 and JT9D-7R4D/E STRUTS FIGURE 2 Part 4 54-50-07 page 9 Figure 2. Material: 2024-T3. Includes Test Report and Certificate of Conformance. | 2 | |
| NDT7001P | BOEING LUCITE WEDGE WITH A .315"Ø FLAT BOTTOM HOLE, 2.010" RADIUS FOR A .25"Ø STRAIGHT BEAM TRANSDUCER. USED WITH REFERENCE STANDARD NDT7001. | 1 | |
| NDT745 | BOEING REFERENCE STANDARD 777 PT 6 57-20-01 FASTENER (BACB30WQ7K15L + BACN10TN7K). Includes Test Report and Certificate of Conformance. | 2 | |
| NDT773-G1 | TRANSDUCER GUIDE THE TRANSDUCER GUIDE IS USED WITH REFERENCE STANDARD NDT773 ONLY | 2 | |
| NDT797 | BOEING REFERENCE STANDARD 777-200/300 PART 4 53-40-06 PG.11 FIGURE 2. MATERIAL: 7075-T7 ALUMINUM WITH GRAIN DIRECTION. Includes Test Report and Certificate of Conformance. | 3 | |
| NDT799 | 2. HONEYCOMB SANDWICH REFERENCE STANDARD (MAX SKIN THICKNESS OF 0.090 INCHES – 2.29MM) | 2 | |
| NDT813 | Reference Standard 0.200" Length x 0.040" Deep x 0.010" width; 6AL-4V | 1 | |
| NDT814 | Reference Standard; .200" long x 0.040" deep x 0.010" width; 6AL-4V | 1 | |
| NEC-6252 | boeing ec reference standard w/cert | 1 | |
| NRK-3S/17-4 | CUSTOM NAVY REFERENCE STANDARD. MATERIAL: 17-4PH TH1050 STAINLESS STEEL. CONTAINS 20 FASTENER HOLES (.156-.750) WITH A TOTAL OF 71 EDM NOTCHES. Includes Test Report and Certificate of Conformance. | 1 | |
| NRK-3S/17-7 | CUSTOM NAVY REFERENCE STANDARD. MATERIAL: 17-7PH STAINLESS STEEL. CONTAINS 20 FASTENER HOLES (.156-.750) WITH A TOTAL OF 71 EDM NOTCHES. Includes Test Report and Certificate of Conformance. | 1 | |
| PWA84314 | REFERENCE STANDARD FOR EDDY CURRENT TEST ON PW2000 SERIES ENGINE FAN BLADES | 1 | |
| QO-QTS-TI-03-001 | Air Force reference standard Detail#1. Material 7075-T6 Aluminum. EDM Notch size: .050" x .050" x .005" Max Width, 10 Flaws total. Includes Test Report and Certificate of Conformance. | 1 | |
| R&D-SHEAR WAVE-EDGE-TI | BOEING REFERENCE STANDARD R&D SHEAR WAVE EDGE | 1 | |
| RH-4-37 | 4-37 Reference Standard, 7075-T6 Aluminum, per drawing | 1 | |
| RH12-T40-7075T6 | CALIBRATION REFERENCE STANDARD (CRS), ALUMINUM ALLOY, CONDUCTIVITY VALUE OF 35% TO 45% IACS THAT CONTAINS VARIOUS HOLE SIZES WITH 0.040 IN. (1.02 MM) DEEP ELECTRICAL DISCHARGE MACHINED (EDM) NOTCHES (TECHNA NDT OR EQUIVALENT) | 1 | |
| RH120-6AL4V-VM-1 | Hole reference Standard, T6AL4V Steel, 3/16" to 3/4", ea. hold .020" deep x 0.004" +/- 0.002" wide edm thru notch | 1 | |
| RH120-C20-4340 | 12 Hole Reference Standard, 3/16" to 3/4", with .020" corner notch, 4340 Steel | 1 | |
| RH120-C30-2024T3 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch, 2024-T3 Aluminum | 1 | |
| RH120-C30-4340 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch, 4340 steel | 1 | |
| RH120-C30-7075T6 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch, 7075T6 Aluminum | 1 | |
| RH120-C30-T6AL4V | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch, 6AL-4V Titanium | 1 | |
| RH120-C30M20-2024T3 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, 2024-T3 Aluminum | 1 | |
| RH120-C30M20-304L | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, 304L | 1 | |
| RH120-C30M20-4130 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, 4130 Steel | 1 | |
| RH120-C30M20-4340 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, 4340 | 1 | |
| RH120-C30M20-7075T76 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, 7075-T76 Aluminum | 1 | |
| RH120-C30M20-MAG | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, Magnesium | 1 | |
| RH120-C30M20-PH13-8MO | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch, PH-13-8 MO | 1 | |
| RH120-C30M20-T6AL4V | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 midwall notch,T6AL4V Titanium | 1 | |
| RH120-C30M30-155PH | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .030 midwall notch, 15-5PH | 1 | |
| RH120-C30T20-7075T6 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" corner notch and .020 thru notch, 7075T6 Aluminum | 1 | |
| RH120-C50-6AL4V | 12 Hole Reference Standard, 3/16" to 3/4", with .050" corner notch, 6AL-4V | 1 | |
| RH120-M20-4340 | 12 Hole Reference Standard, 3/16" to 3/4", with .020" midwall notch, 4340 | 1 | |
| RH120-M30-4340 | 12 Hole Reference Standard, 3/16" to 3/4", with .030" mid-wall notch, 4340 steel | 1 | |
| RH120-T20-T6AL4V | 12 Hole Reference Standard, 3/16" to 3/4", with .020" thru notch, 6AL-4V | 1 | |
| RH120-T40-7475T7 | 12 Hole Reference Standard, 3/16" to 3/4", with .040" thru notch, 7475T7 | 1 | |
| RH121-C30-155 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notches, 15-5PH | 1 | |
| RH121-C30-2024T3 | 12 Hole Reference Standard, 1/8" to 3/4", with .030" corner notch, 2024-T3 Aluminum | 1 | |
| RH121-C30-4340 | 12 Hole Reference Standard, 1/8" to 3/4", with .030" corner notch, 4340 Steel | 1 | |
| RH121-C30-7075T6 | 12 Hole Reference Standard, 1/8" to 3/4", with .030" corner notch, 7075-T6 Aluminum | 1 | |
| RH121-C30C20-7075T6 | 12 Hole Reference Standard, 1/8" to 3/4", with .030" corner notch & .020" corner notch, 7075-T6 Aluminum | 1 | |
| RH121-C30M20-155 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notches,.020" Midwall notches 15-5PH | 1 | |
| RH121-C30M20-2024T3 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notches,.020" Midwall notches, 2024-T3 | 1 | |
| RH121-C30M20-7075T6 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notches,.020" Midwall notches, 7075-T6 | 1 | |
| RH121-C30T20-7075T6 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notch, .020"thru notch, 7075-T6 | 1 | |
| RH121-C30T20-T6AL4V | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notch, .020"thru notch, T6AL4V | 1 | |
| RH121-C50-T6AL4V | 12 Hole Reference Standard, 1/8" to 3/4", with .050" corner notch, 6AL4V Titanium | 1 | |
| RH121-M20-4340 | 12 Hole Reference Standard, 1/8" to 3/4", with .020" Mid Wall notch, 4340 Steel | 1 | |
| RH121-M20-7075T6 | 12 Hole Reference Standard, 1/8" to 3/4", with .020" Mid Wall notch, 7075-T6 Aluminum | 1 | |
| RH121-M20-T6AL4V | 12 Hole Reference Standard, 1/8" to 3/4", with .020" Mid Wall notch, 6AL4V Titanium | 1 | |
| RH122-T20-2024T3 | 12 Hole Reference Standard, 5/32" to 13/16", with .020" thru notch, 2024-T3 Aluminum | 1 | |
| RH122-T40-7075T6 | 12 Hole Reference Standard, 5/32" to 13/16", with .040" thru notch, 7075-T6 Aluminum | 1 | |
| RH13-M20-2024T3 | 13 Hole Reference Standard, Midwall Notch, 2024-T3 AL holes sizes 1/8, 5/32, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4, 7/8, 1.0 | 1 | |
| RH13-M40-2024T3 | 13 Hole Reference Standard, Midwall Notch, 2024-T3 AL holes sizes 1/8, 5/32, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4, 7/8, 1.0 | 1 | |
| RH13-T20-304 | 13 Hole Reference Standard, 5/32" thru 9/16" with 0.20" thru, 304 .. | 1 | |
| RH13-T20-4340 | 13 Hole Reference Standard, 5/32" thru 9/16" with 0.20" thru, 4340 | 1 | |
| RH13-T20-7075T6 | 13 hole reference standard, hole sizes 5/32" thru 9/16" with 0.20" thru 7075T6 | 1 | |
| RH13-T20-T6AL4V | 13 Hole Reference Standard, 5/32" thru 9/16" with 0.20" thru T6AL4V Ti. | 1 | |
| RH200-C30-304L | 20 Hole Reference Standard, 1/8" Thru 3/4", w/.030" Cornor Notch, 304L Stainless | 1 | |
| RH200-C30-7075T6 | 20 Hole Reference Standard, 1/8" Thru 3/4", w/.030" Corner Notch, 7075T6 | 1 | |
| RH200-C30M20-2024T3 | 20 Hole Reference Standard, 1/8" Thru 3/4", w/.030" Corner Notches and .020" Midwall, 2024-T3 | 1 | |
| RH200-C50-T6AL4V | 20 Hole Reference Standard, 1/8" Thru 3/4", w/.050" Corner Notch, 6AL-4V | 1 | |
| RH200-T20-7075T6 | 20 Hole Reference Standard, 1/8" thru 3/4", w/.030" thru Notch, 7075T6 | 1 | |
| RH7-C30T20-T6AL4V | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, .030" Corner, Titanium | 1 | |
| RH7-T20-T6AL4V | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, Titanium | 1 | |
| RH70-C30T20-2024T3 | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, .030" Corner, 2024-T3 | 1 | |
| RH70-T20-177 | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, 17-7PH Stainless | 1 | |
| RH70-T20-2024T3 | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, Aluminum | 1 | |
| RH70-T20-7075T6 | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, Aluminum | 1 | |
| RH70-T20-T6AL4V | Hole Reference Standard, 7 holes, 5/32” thru 1/2” w/ .020” thru-wall notches, Titanium | 1 | |
| RH71-T20-T6AL4V | Hole Reference Standard, 7 holes, 1/8",5/32,3/16,7/32,1/4,9/32,5/16" w/ .020” thru-wall notches, Titanium | 1 | |
| RM121-C30T20-4340 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notch, .020"thru notch, 008", .020", .040", 4340 | 1 | |
| RM121-C30T20-6AL4V | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notch, .020"thru notch, 008", .020", .040", 6AL-4V | 1 | |
| RM121-C30T20-7075T6 | 12 Hole Reference Standard, 1/8" thru 3/4", w/.030" corner notch, .020"thru notch, 008", .020", .040", 7075-T6 | 1 | |
| RM200-C20T20-T6AL4V | 20 Hole Reference Standard, 1/8" Thru 3/4", w/20" Cornor Notch, w/ .20" Thru Notch, T6AL4V, Plus .008", .020" & .040" surface notches | 1 | |
| RM200-T40-T6AL4V | CALIBRATION REFERENCE STANDARD, TITANIUM ALLOY, CONDUCTIVITY 1.1 % IACS, CONTAINS 0.010 IN. (0.25 MM), 0.020 IN. (0.51 MM), AND 0.040 IN. (1.02 MM) DEEP SURFACE ELECTRICAL DISCHARGE MACHINED NOTCHES, AND VARIOUS SIZE HOLES WITH 0.040-IN (1.02 MM) EDM NOTC | 1 | |
| RM290-C30-7075T6 | Reference Standard, 29 Holes 1/8" thru 1" in 1/32" increments with .030" corner notch plus 3 surface notch | 1 | |
| RM290-T20-2014T6 | multi-hole reference standard 29 holes 1/8, 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 13/32, 7/16, 15/32, 1/2, 17/32, 9/16, 19/32, 5/8, 31/32, 11/16, 23/32, 3/4, 25/32, 13/16, 27/32, 7/8, 29/32 15/16, 31/32 0.020 deep through notch 3 surface flaws... | 1 | |
| RS0824-4340-VMS3RS-062 | Reference Standards are 3” Long x 2” Wide x ¼” Thick, 3 Surface EDM notches: 0.008” deep x 0.062” long, 0.020” deep x 0.062” long and 0.040” deep x 0.062” long | 1 | |
| S41-E1A | BOEING CUSTOM REFERENCE STANDARD MCU ESM S41-E1A NDI REF STD PER DRAWING SK667-00011. | 1 | |
| S41-E1C | BOEING CUSTOM REFERENCE STANDARD MCU ESM S41-E1C NDI REF STD PER DRAWING SK667-00012. | 1 | |
| S41-F1B | BOEING CUSTOM REFERENCE STANDARD MCU ESM S41-F1B NDI REF STD PER DRAWING SK667-00010. | 1 | |
| SAAB 5512-332-03I | SAAB 340 REFERENCE STANDARD 5512-332-03I FIGURE 1 PAGE 2, 55-10-00 PART 6 PAGE 3. MATERIAL: 2024-T351 ALUMINUM WITH 4 HL10 VAP-6-7 HI-LOK FASTENERS.. Includes Test Reprort and Certificate of Conformance. | 1 | |
| SB 146/53-167/2 | BAE 146-RJ SERIES REFERENCE STANDARD ISB.53-167 APPENDIX 2 DRAWING 15, PAGE 23&24. Material: Substitute 2024-T3 Clad for 2014A-T4 Aluminum. Includes Test Report and Certificate of Conformance. | 1 | |
| SB09540030-5 | DC9 SURFACE REFERENCE REFERENCE STANDARD DC9-54-030. MATERIAL: 17-7 PH STAINLESS STEEL. EDM NOTCH: 0.002"-0.010" WIDE x 0.030" DEEP. | 1 | |
| SLS-123456-SS304 | BOEING REFERENCE STANDARD PER DRAWING STD-1. MATERIAL: 304 STAINLESS STEEL. CHEMICAL CONVERSION COATING PER MIL-DTL-5541, CLASS 1A. Includes Certification Traceable to NIST and Material Certs. | 1 | |
| SPT- RM200-C20T20-T6AL4V | 20 Hole Reference Standard, 1/8" Thru 3/4", w/20" Cornor Notch, w/ .20" Thru Notch, T6AL4V, Plus .008", .020" & .040" surface notches | 1 | |
| SRSM-2510A | ec reference standard w/certs | 1 | |
| SRSM-51020S/WLD | urface reference standard, 4340 Steel, with EDM notch depths of 0.5mm", 1.0" and 2.0mm +/-1.3mm1 (0.2mm, 0.51mm and 1.02mm), Notch Width: .18mm Max. Depth: +/- .03mm. Reference standard overall dImensions 25.4mm X 101.6mm X 6.4mm). Includes Test Report a | 1 | |
| ST4130 | BOMBARDIER / CANADAIR EDDY CURRENT SURFACE REFERENCE STANDARD PART 6 55-20-001, NOTCHES .008", .020", .040" (.005" Wide +000 / - .002 and +/- .001" Depth), MATERIAL: 4130 STEEL. Includes certification Report and Certificate of Conformance(COC)... | 1 | |
| ST8870-7 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE( 1-10 PLY), PT 1 51-04-00, PAGE 21 FIGURE 8. SUPPLIED WITH HOLDING BLOCK | 4 | |
| ST8870-8 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE( 11-20 PLY), PT 1 51-04-00, PAGE 21 FIGURE 8. SUPPLIED WITH HOLDING BLOCK | 5 | |
| ST8870-9 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE( 21-30 PLY), PT 1 51-04-00, PAGE 19 FIGURE 8. SUPPLIED WITH HOLDING BLOCK | 4 | |
| ST8870B-7 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATE. MATERIAL: BMS8-79 FIBERGLASS( 1-10 PLY), PT 1 51-04-00, PAGE 27 FIGURE 8. B737 NDT Part 1, 51-04-00. Includes C-Scan, Certification Report and Certificate of Conformance. | 3 | |
| ST8870B-8 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATE. MATERIAL: BMS8-79 FIBERGLASS( 11-20 PLY), PT 1 51-04-00, PAGE 27 FIGURE 8. B737 NDT Part 1, 51-04-00. Includes C-Scan, Certification Report and Certificate of Conformance. | 3 | |
| ST8870B-9 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATE. MATERIAL: BMS8-79 FIBERGLASS( 21-30 PLY), PT 1 51-04-00, PAGE 27 FIGURE 8. B737 NDT Part 1, 51-04-00. Includes C-Scan, Certification Report and Certificate of Conformance. | 3 | |
| ST8870C-7 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATEBMS8-139 FIBERGLASS( 1-10 PLY), PT 1 51-04-00, PAGE 28 FIGURE 8. Includes C-Scan, Certification Report and Certificate of Conformance. | 2 | |
| ST8870C-8 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATEBMS8-139 FIBERGLASS( 11-20 PLY), PT 1 51-04-00, PAGE 28 FIGURE 8. Includes C-Scan, Certification Report and Certificate of Conformance. | 2 | |
| ST8870C-9 | BOEING REFERENCE STANDARD, COMPOSITE LAMINATE STEP WEDGE WITH HOLDING PLATEBMS8-139 FIBERGLASS( 21-30 PLY), PT 1 51-04-00, PAGE 28 FIGURE 8. Includes C-Scan, Certification Report and Certificate of Conformance. | 2 | |
| STANDARD-B | 2/64" FLAT BOTTOM HOLE EQUIVALENT SURFACE NOTCH STANDARD (*ABOVE DESCRIPTION MUST BE ENGRAVED ON THE REFERENCE STANDARD) ..DRAWING "B" (PS21211.3 FOR F/A-18 OUTER WING FORWARD SPAR) MATERIAL=7075-T6 | 1 | |
| TEK-186-2024T3-12 | 12 Hole Reference Standard Similar to Boeing 186, 3/16" to 3/4", with .030" corner and .020" corner notches on the bottom plate, .040 Long x .020 Deep Midwall Notches on the top plate. 2024-T3 | 1 | |
| TEK-5154 | CUSTOM 2 ELEMENT RING TRANSDUCER FOR BORE HOLE INSPECTION WITH BOEING REFERENCE STANDARD 55-10-13 PAGE 9 FIGURE 2. TWO MICRODOT CONNECTORS "A" AND "B" | 1 | |
| TEK-6034F | REFERENCE STANDARD_WHEEL MATERIAL : AL ALLOY 2014-T6 | 1 | |
| TEK-9087L | 5 MHZ SURFACEWAVE TRANSDUCER, REFERENCE STANDARD NDT3310, LEFT SOUND DIRECTION | 1 | |
| TEK-9087R | 5 MHZ SURFACEWAVE TRANSDUCER, REFERENCE STANDARD NDT3310, RIGHT SOUND DIRECTION | 1 | |
| U8860407 | ALUMINUM (7075-T6) MULTI-HOLE REFERENCE STANDARD WITH CERTIFICATE TRACEABLE TO NIST | 1 | |
| V1 | V1 STANDARD REFERENCE STANDARD IIW 1 (TYPE V1), MADE FROM ALUMINUM | 3 | |
| W-19-1 | Boeing W-19 Reference Standard.-1 Assembly | 1 | |
| W-87 REF STD IBD | BOEING REFERENCE STANDARD. W-87 INBOARD 360 REFERENCE STANDARD. Materials: 2024-T351 and 7075-T651 Aluminum. Includes Test Report Traceable to NIST. | 1 | |
| W-87 REF STD OBD | BOEING REFERENCE STANDARD. W-87 OUTBOARD 360 REFERENCE STANDARD. Materials: 2024-T351 and 7075-T651 Aluminum. Includes Test Report Traceable to NIST. | 1 | |
| WNG-3NDI-XRS599-03 | Reference standard, Lower Skin Layer | 1 | |
| WNG-CB-Repair-0.622 | NDI CB Repair Reference Standard .622 diameter hole, 2" Wide x 11" Long, T=.272" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.685 | NDI CB Repair Reference Standard .685 diameter hole, 2" Wide x 11" Long, T=.320" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.747 | NDI CB Repair Reference Standard .747 diameter hole, 2" Wide x 11" Long, T=.389" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.810 | NDI CB Repair Reference Standard .810 diameter hole, 2" Wide x 11" Long, T=.500" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.870 | NDI CB Repair Reference Standard .870 diameter hole, 2" Wide x 11" Long, T=.272" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.932 | NDI CB Repair Reference Standard .932 diameter hole, 2" Wide x 11" Long, T=.563" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-0.997 | NDI CB Repair Reference Standard .997 diameter hole, 2" Wide x 11" Long, T=.583" Thick, T2=.500" Thick | 1 | |
| WNG-CB-Repair-1.057 | NDI CB Repair Reference Standard 1.057 diameter hole, 2" Wide x 11" Long, T=.583" Thick, T2=.500" Thick | 1 | |
| WNG-Steel-Doubler-0.625 | NDI Steel Doubler Reference Standard .625" diameter hole, 2" Wide x 11" Long, T=.500" Thick, T2=.500" Thick, 17-4PH | 1 | |
| WNG-Steel-Doubler-1.125 | NDI Steel Doubler Reference Standard 1.125" diameter hole, 2" Wide x 11" Long, T=.500" Thick, T2=.500" Thick, 17-4PH | 1 |
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
