| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| TMY20-79-001 | OIL FIXTURE | 1 |
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| (CALIB) RRT061249-1 | Fixture - Oil Pump (CALIBRATION) (CALIBRATION) | 1 | |
| 10C1087G01 | FIXTURE, PULLER - NO. 5 BEARING AIR/OIL SEPARATOR (PULLER FIXTURE) | 1 | |
| 10C1222 | FIXTURE - I/R - AIR/OIL SEPARAT | 1 | |
| 10C1222G01 | FIXTURE, INSTALL/REMOVE - AIR/OIL SEPARATOR NUT | 1 | |
| 10C1222G02 | Fixture, Install/Remove Air/Oil Separator Nut | 1 | |
| 10C1223 | FIXTURE, PULLER - OIL INLET CO | 1 | |
| 10C1223G01 | FIXTURE, PULLER - OIL INLET COVER (PULLER FIXTURE) | 1 | |
| 10C1344 | FIXTURE, PULLER- NO 5 BEARING AIR/OIL SEPARATOR | 1 | |
| 10C1344G01 | Fixture，puller-No 5 bearing air/oil separator | 1 | |
| 10C3111G01 | Fixture,installation-oil separator nut | 1 | |
| 11C3206 | FIXTURE - TARGET-OIL NOZZLE - NO. 1 BRG | 1 | |
| 11C3206G01 | FIXTURE, TARGET - OIL NOZZLE, NO. 1 BEARING | 1 | |
| 11C3455 | FIXTURE - ALIGNMENT TUBE NO. 1 BEARING OIL SUPPLY | 1 | |
| 11C3596 | FIXTURE - PLUG - NO. 5 BEARING OIL FLOW (FLOW CHECK FIXTURE) | 1 | |
| 11C3927G01 | Tool Set Oil Flow Test Fixture Tgbx | 1 | |
| 11C4215 | FIXTURE - RESTRAINING SEAL AIR/OIL ROT NO 4 BRG | 1 | |
| 11C4229G01 | Fixture,restraining-seal rotating oil rear no 3 bearing | 1 | |
| 11C4472 | FIXTURE - INSTALL/REMOVE-COOLER OIL-AIR COOLED | 1 | |
| 11C4472G01 | SPL-11575 - FIXTURE - REMOVE/INSTALL, AIR COOLED OIL COOLER | 1 | |
| 11C4472G02 | SPL-11575 - FIXTURE - REMOVE/INSTALL, AIR COOLED OIL COOLER | 1 | |
| 11C4693G01 | FIXTURE, INSTALL/REMOVE - MAIN FUEL OIL HEAT EXCHANGER | 1 | |
| 14406 | FIXTURE, MAIN OIL SCREEN ASSY | 1 | |
| 18C1071 | FIXTURE, ALIGNMENT - OIL NOZZLE, NO5 | 1 | |
| 18C1071G01 | Fixture,alignment - oil nozzle,no 5 | 1 | |
| 18C1552 | FIXTURE, FLOW CHECK - OIL | 1 | |
| 18C1552G01 | Fixture, Flow Check - Oil Damper, No 3 Brg | 1 | |
| 19C0628G01 | Fixture Install-Aft Seals Inner Race&Oil Scoop No 4 Bearing | 1 | |
| 1C9355 | FIXTURE, ASSEMBLY IMPINGEMENT - NO.1 BRG OIL NOZZL | 1 | |
| 1P16071 | FIXTURE, OIL FLOW [IAE1P16266] | 1 | |
| 23030254 | FIXTURE, OIL PUMP SCAV RG | 1 | |
| 23050254 | FIXTURE, OIL PUMP SCAV RG | 1 | |
| 23068636 | Fixture- Oil Flow, Aft Sump Cover | 1 | |
| 2C18118 | FIXTURE, GAGE GO- STATIONARY AIR/OIL SEAL, NO 4 BRG | 1 | |
| 2C5248P01 | FIXTURE - #7 OIL NOZZLE | 1 | |
| 2C6084G04 | LIFT FIXTURE - NO.#5 RET. NUT/OIL TUBE | 1 | |
| 2C6260 | FIXTURE, ALIGNMENT- STATIONARY OIL | 1 | |
| 2C6260G01 | Fixture,alighment-stationary oil seal | 1 | |
| 2C8040G01TK | FIXTURE CONCENTRICITY-NO.3 BRG. STATIONARY AIR &OIL SEALS | 1 | |
| 2C81327G01 | Fixture, Puller - No 4 Oil Seal & Inner Race | 1 | |
| 2C81328G01 | Fixture,puller-No 4 oil seal,hpt rotor | 1 | |
| 2C91097G01 | FIXTURE - OIL TANK HOLDING | 1 | |
| 2C91354 | FIXTURE, HOLDING-SENSOR BYPASS FILTER, OIL | 1 | |
| 2C91354G01 | Holding Fixture − Oil Filter By− Pass Sensor (Alternate) | 5 | |
| 2C91354G02 | Holding Fixture − Oil Filter By− Pass Sensor (Recommended) | 10 | |
| 3212902-1 | APU OIL LEAK FIXTURE | 1 | |
| 5120-01-137-3557 | OIL TUBE FIXTURE PACKAGING: D-LM-008-036/SF-000 QAC:C | 1 | |
| 6796137 | ALIGNING FIXTURE - OIL TUBE | 1 | |
| 6799596 | SHAFT GEAR OIL SEAL FIXTURE - INSTALLATION, SPEED | 2 | |
| 6799708 | Fixture â Alignment, Inner Combustion Chamber Oil Tubes | 2 | |
| 6872760 | FIXTURE - MACHINING, OIL FILTER | 1 | |
| 856A1171 | FIXTURE, PRESS TEST NO 3 BRG AFT AIR/OIL SEAL | 1 | |
| 856A1171G03 | Fixture,press test No3 brg aft air&oil seal | 1 | |
| 856A1171G06 | FIXTURE, PRESS TEST, #3 BRG AFT AIR/OIL SEAL | 2 | |
| 856A2873G01 | INSTALLATION FIXTURE - OIL DISTRIBUTOR GEAR 61 TOOTH | 2 | |
| 856A3265G04 | MACHING FIXTURE FOR OIL DAMPER NO.5 BEARING | 4 | |
| 856A3412 | FIXTURE, LOCKING - OIL DISTRIBUTOR, HORIZONTAL BEVEL GEAR, TGB (LOCKING FIXTURE) | 1 | |
| 856A3739 | INSTALLATION FIXTURE - OIL NOZZLE N 2 BRG | 1 | |
| 856A3739G01 | Fixture Install Oil Nozzle Bearing 2 | 1 | |
| 856A3739G02 | Fixture, Installation - No. 2 Bearing Oil Nozzle (installation fixture) | 3 | |
| 856A4026G02 | Fixture,holding-no.3 brg fwd stationary oil seal | 1 | |
| 856A5611G02 | FIXTURE WELDING OIL TUBES OF TURBINE FRAME | 2 | |
| 8C2022G01 | Fixture, rtnr - no 4 brg inner race/oil scoop/ rotating seal/fwd seal | 1 | |
| 8C2047G01 | fixture removal fwd rotating seal oil hptr | 1 | |
| 8C2900 | FIXTURE, TEST - OIL SUPPLY, NO 1 & 2 BRG | 1 | |
| 8C2917 | FIXTURE, ALIGNMENT TUBE NO. 1 BEARING OIL SUPPLY | 1 | |
| 8C2971G01 | Fixture Restraint-N1B Rotating Oil Seal | 1 | |
| 9441M58 | FIXTURE, SUPPORT AIR-OIL | 1 | |
| 9441M58 REV C | FIXTURE, SUPPORT AIR-OIL | 1 | |
| 9481M87G01 | FIXTURE, TEST STAND - OIL FLOW | 1 | |
| 956A1031 | FIXTURE - RTNR-NO 4 BRG INNER RACE/OIL SCOOP/ROTATING SEAL/FWD SEAL | 1 | |
| 956A1037 | FIXTURE - RESTRAINING - FWD ROTATING OIL SEAL NO. 4 BEARING | 1 | |
| 956A1037G01 | Fixture,restraining-fwd rotating oil seal no 4 bearing | 1 | |
| 956A1037G02 | Fixture,restraining-fwd rotating oil seal no 4 bearing | 1 | |
| 956A1049 | FIXTURE - REMOVE - NO 4 OIL SCOOP | 1 | |
| 956A1064 | FIXTURE - INSTALL - STATIONARY OIL SEAL - FWD | 1 | |
| 956A1064G02 | Install Fixture - Stationary Oil Seal, Fwd | 1 | |
| 956A1515 | FIXTURE - REMOVAL - NO 3B BRB FWD IR/OIL DISTRIBUTER | 1 | |
| 956A1515G01 | Fixture removal no 3b brg fwd ir oil distributor | 1 | |
| 956A1805 | FIXTURE - RESTRAIN - SEAL ROTATING - OIL | 1 | |
| 956A1805G02 | ROTATING OIL SEAL RESTRAIN FIXTURE | 1 | |
| 956A3031 | FIXTURE - RTNR-NO 4 BRG INNER RACE/OIL SCOOP/ROTATING SEAL/FWD SEAL | 1 | |
| 956A3049 | FIXTURE - REMOVE - NO 4 OIL SCOOP | 1 | |
| 956A3064G01 | Fixture, Installstationary Oil & Air Seals, Fwd | 1 | |
| 956A3092 | FIXTURE - ALIGNMENT - OIL TUBES | 1 | |
| 956A3092G02 | Fixture,alignment-oil tubes | 1 | |
| 956A3504G01 | ffixture install remove seal rotating oil number 3 bearing | 1 | |
| 956A3535 | FIXTURE - REMOVAL - OIL SCOOP - NO 3 BRG | 1 | |
| 956A3535G01 | Fixture, Removaloil Scoop No 3 Brg | 1 | |
| 956A3805 | FIXTURE - RESTRAIN - AFT ROTATING OIL SEAL - NO 4 BRG | 1 | |
| 956A3805G01 | Fixture, Restrai-Aft Rotating Oil Seal,No 4 Brg | 1 | |
| 956A6128 | FIXTURE - REMOVE - OIL SUPPLY - FAN HUB | 1 | |
| 956A6128G01 | Fixture Remove-Oil Supply Fan Hub | 1 | |
| 956A6568 | FIXTURE - PULLER - TRF - OIL SCAVENGE | 1 | |
| 956A6568G01 | Fixture puller trf oil scavenge | 1 | |
| 956A6622 | FIXTURE - DRY OUT AND RELUB - ENGINE OIL SYSTEM | 1 | |
| 956A6669G01 | Fixture ,oil cover handle out | 1 | |
| 956A6670G01 | Fixture,induction heating-cover oil inlet out | 1 | |
| 956A6670G02 | Fixture,induction heating-cover oil inlet out | 1 | |
| 956A7027G01 | Fixture,lift and turn-oil tank outillage de manutention reservoir d huile | 1 | |
| 956A7660 | FIXTURE, SUPPORT OIL TUBE — LPT CASE | 1 | |
| 956A7660G01 | FIXTURE,SUPPORT OIL TUBE-LPT CASE | 1 | |
| 956A7680 | FIXTURE- OIL TANK PROTECTOR - ENGINE ASSEMBLY | 1 | |
| 956A8025 | FIXTURE - CHECK - NOZZLE - OIL BEARING 2 | 1 | |
| 956A8025G01 | Fixture，check-nozzle,oil bearing 2 | 1 | |
| 956A8547 | FIXTURE - HOLDING - BRACKETS - OIL DRAIN | 1 | |
| 956A8547G01 | Fixture，holding-brackets，oil drain outillage maintien drain 6H | 1 | |
| A27043-1 | TEST EQUIPMENT FIXTURE - INBD/OUTBD SPOILER ACTUATOR | 1 | |
| C107-00-0085 | INLET FITTING OILING FIXTURE | 1 | |
| CF65B80578 | CHECK FIXTURE - QUADRANT LEVER AND BRACKET ASSEMBLY, INBOARD SPOILER | 1 | |
| CF65B80836 | CHECK FIXTURE - SPOILER CONTROL, DIFFERENTIAL MECHANISM | 1 | |
| CPWA-30432 | Test fixture, oil relief valve | 1 | |
| F-3501734-1 | OIL GEAR PUMP ASSEMBLY FIXTURE | 1 | |
| FS0002 | Fixture- Oil Bypass Valve | 1 | |
| FS0021 | OIL BYPASS VALVE FIXTURE | 1 | |
| G600-270016-105 | Fixture - Inboard And Outboard Flaps And Flight Spoiler Rigging (Lh) | 4 | |
| G600-270016-106 | Fixture - Inboard And Outboard Flaps And Flight Spoiler Rigging (Rh) | 4 | |
| G600-270016-106 | FIXTURE FLAP & FLIGHT SPOILER | 4 | |
| G600-270016−105 | FIXTURE - INBOARD AND OUTBOARD FLAPS AND FLIGHT SPOILER RIGGING (LH) | 4 | |
| G600-270016−106 | FIXTURE - INBOARD AND OUTBOARD FLAPS AND FLIGHT SPOILER RIGGING (RH) | 4 | |
| G600-270032-1 | FIXTURE GROUND SUPPORT SPOILER | 1 | |
| G600-270032-101 | FIXTURE-GROUND SUPPORT SPOILER | 1 | |
| G600−270016−105 | FIXTURE − INBOARD AND OUTBOARD FLAPS AND FLIGHT SPOILER RIGGING (LH) | 4 | |
| G600−270016−106 | FIXTURE − INBOARD AND OUTBOARD FLAPS AND FLIGHT SPOILER RIGGING (RH) | 4 | |
| GS10376 | FIXTURE, PROPELLER OIL TEST | 1 | |
| GS10757 | OIL PRESSURE RELIEF VALVE FIXTURE | 1 | |
| GS22267-01 | FIXTURE, OIL BATH | 1 | |
| GS22267-1 | OIL BATH FIXTURE | 2 | |
| HS7623 | FIXTURE-OIL INDICATOR ADJUSTING | 1 | |
| HS8961 | FIXTURE - PROPELLER OIL TEST | 2 | |
| HSP1584 | OIL TEST FIXTURE PULLER | 1 | |
| IAE1P16074 | FIXTURE, OIL FLOW | 1 | |
| LTCT1247-01 | Fixture, Test, Oil Pressure | 1 | |
| LTCT14794-01 | Fixture, Holding, Air/Oil Separator Gear Wrench | 1 | |
| LTCT4535 | FIXTURE, OIL PRESSURE | 1 | |
| LTCT4900 | FIXTURE,TEST,OIL FLOW,POWER SHAF | 1 | |
| LTCT5426X | Fixture, Oil Flow | 1 | |
| LTCT7202-01 | OIL TUBE FIXTURE PACKAGING: D-LM-008-036/SF-000 QAC:C | 1 | |
| LTCT7229-01 | Fixture, Carrier Assembly, Oil Target | 1 | |
| LTCT7515-01 | Fixture, No. 3 Bearing Housing Support Oil Flow | 1 | |
| LTCT7539-01 | Fixture Assembly, Oil Tube Target | 1 | |
| LTCT7632-01 | Fixture, Carrier Assembly, Oil Flow Target | 1 | |
| PWA 25057 | OIL FLOW FIXTURE | 1 | |
| PWA 25257 | OIL FLOW FIXTURE | 2 | |
| PWA 7153 | FIXTURE OIL SCREEN HOLDING | 1 | |
| PWA 85546 | FIXTURE, OIL FLOW | 1 | |
| PWA 85547 | FIXTURE, OIL FLOW | 1 | |
| PWA 85550 | FIXTURE, OIL FLOW | 1 | |
| PWA 85935 | FIXTURE, OIL FLOW | 1 | |
| PWA 85980 | FIXTURE, OIL FLOW | 1 | |
| PWA 88135 | FIXTURE, OIL FLOW | 1 | |
| PWA12092 | FIXTURE OIL SCREEN | 1 | |
| PWA211073 | FIXTURE, OIL FLOW TEST | 1 | |
| PWA211075 | FIXTURE, OIL FLOW TEST | 1 | |
| PWA211083 | OIL FLOW TEST, FIXTURE | 1 | |
| PWA211089 | OIL FLOW TEST, FIXTURE | 1 | |
| PWA211180 | FIXTURE, OIL FLOW TEST | 1 | |
| PWA212244 | FIXTURE, OIL FLOW - AGBX, MODULE | 1 | |
| PWA25967 | FIXTURE - NOZZLE ASSY, G/BOX OIL FLOW_[PWA25967] | 2 | |
| PWA25968 | FIXTURE - NOZZLE ASSY, GEARBOX OIL FLOW_[PWA25968] | 2 | |
| PWA25970 | FIXTURE - NOZZLE ASSY, GEARBOX OIL FLOW_[PWA25970] | 2 | |
| PWA27656 | FIXTURE - DIFF CASE #3 BRG NOZ OIL FLOW_[PWA27656] | 1 | |
| PWA27860 | FIXTURE - NO1,2 BRG NOZZ OIL FLOW CHK | 2 | |
| PWA28760 | FIXTURE-OIL FLOW | 1 | |
| PWA32316 | FIXTURE - NO.2/3 BRG NOZZLE OIL FLOW | 1 | |
| PWA81311 | FIXTURE - HOLDING, LOWER TOWERSHAFT AND OIL DUCT - PW2000 ENGINES | 1 | |
| PWA86479 | FIXTURE OIL FLOW COMPARTMENT | 1 | |
| PWC30872 | FIXTURE, OIL PRESSURE RELIEF VALVE | 1 | |
| PWC37029 | FIXTURE, LOADING, OIL PUMP DRIVE SHAFT BEARING | 1 | |
| PWC37726 | FIXTURE, LOADING, OIL PUMP TRANSFER SHAFT BEARING | 1 | |
| PWC37834 | FIXTURE, OIL PUMP DRIVE | 3 | |
| PWC42165 | Fixture Flow AGB oil Nozzle | 1 | |
| PWC56097 | FIXTURE, LOADING, OIL PUMP DRIVE GEAR | 1 | |
| PWC60743 | FIXTURE-OIL FLOW | 1 | |
| PWC64605 | MAIN OIL PRESSURE ADJUSTMENT FIXTURE | 3 | |
| PWC66499 | Fixture Oil Pump | 1 | |
| PWC72315 | FIXTURE FLOW - OIL TRANSFER TUBE | 1 | |
| PWC72883 | TEST FLOW FIXTURE, NO.1 BRG OIL NOZZLE | 1 | |
| RB T101549 | Transmission Oil Cooler Holding Fixture | 1 | |
| RB6897878 | Oil Check Valve Test Fixture | 2 | |
| RB6897883 | Oil Filter Delta P Indicator Test Fixture | 2 | |
| RRT061249 | FIXTURE - OIL PUMP | 1 | |
| RRT061249-1 | FIXTURE OIL PUMP | 4 | |
| SPL-10544 | FIXTURE - HOLDING, LOWER TOWERSHAFT AND OIL DUCT | 1 | |
| ST70433 | Fixture, Oil Filter Cap Assembly | 2 | |
| U541483-T2 | VALVE TEST FIXTURE, OIL | 1 | |
| U541483-T5B | FLUSHING FIXTURE, OIL | 1 | |
| XPWA211110 | Fixture oil flow test main gearbox | 1 |
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
