| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| 0274604410 | OIL DUCT | 1 |
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| 6796891 | REDUCTION GEAR OIL FILTER ASSEMBLY TORQUE ADAPTER | 3 | |
| 6798131 | WRENCH - SPANNER, REDUCTION GEAR OIL PUMP PRESSURE ADJUSTING VALVE THREADED BUSHING | 2 | |
| 23034223 | GAGE--TARGETING, OIL ORIFICE POSITION AND FLOW, REDUCTION GEAR REAR HOUSING ASSEMBLY | 1 | |
| 0292720980 | DUCT,OIL | 1 | |
| 0319150380 | DUCT,OIL RETURN | 1 | |
| 0319728200 | PIPE,OIL SUCTION,REDUCTION GEAR | 1 | |
| 06-4035-3600 | SVC UNIT: FL,HYD & OIL, 8GL,MANUAL HAND PUMPTHIS PRODUCT CAN ONLY BE SHIPPED VIA LTL CARRIERS, FREIGHT METHODS WILL BE RESTRICTED. | 10 | |
| 833491-1 | DUCT OIL COOLER | 1 | |
| 856A1216 | PULLER-NO.4 BRG. OUTER RACE, OIL SEAL & AIR DUCT | 2 | |
| 856A1216 G01 | Puller ‐ No. 4 Brg Outer Race Oil Seal & Air Duct | 3 | |
| 856A1216 REV C | PULLER-NO.4 BRG. OUTER RACE, OIL SEAL & AIR DUCT | 1 | |
| 856A1216G01 | PULLER-NO4 BEARING OUTER RACE, OIL SEAL & AIR DUCT | 3 | |
| 856A1216G02 | Puller - No. 4 Bearing Outer Race, Oil Seal and Air Duct (puller) | 12 | |
| 856A1216G03 | PULLER - #4 BRG OUTER RACE - OIL SEAL & AIR DUCT | 1 | |
| 856A2640 | HOLDER OIL SEPARATOR DUCT | 1 | |
| 856A2640G01 | HOLDER OIL SEPARATOR DUCT | 8 | |
| 856A2920G02 | TOOL SET, HOLDING - AIR/OIL SEPARATOR TORLON DUCTS | 3 | |
| 856AI2I6 | PULLER-NO.4 BRG. OUTER RACE, OIL SEAL & AIR DUCT | 1 | |
| 956A1078 | COIL - INDUCTION - INVERTED CONFIGURATION | 1 | |
| 98D10007513000 | COVER-OILCOOLER OUTLET,APU ( THIS TOOL IS USED TO KEEP OUT DIRT, MOISTURE OR FOREIGN OBJECTS WHICH CAN GET INTO THE OILCOOLER OUTLET DUCT. YOU CAN CLOSE THE APU OILCOOLER OUTLET DUCT WITH THE COVER WHEN THE AI RCRAFT IS PARKED AND THE APU IS SWITCHED OFF. | 16 | |
| 9C1946 | OIL DUCT ASSY/DISASSY HORIZONTAL AXIS | 1 | |
| 9C1947 | OIL DUCT ASSY/DISASSY VERTICAL AXIS | 1 | |
| ACN16-M12 | 16 Pin Lemo to Microdot NPID-1024 cable with No balance coil. Used with N500 series and N600 series instruments with internal balance coils. Note*** Olympus web information for this product is incorrect. The Nortec 2000D and Nortec 2000D+ do not have i | 1 | |
| ACN16-MD15 | 16 Pin to Microdot NPID-1024 cable 15ft long with No balance coil. Used with N500 series and N600 series instruments with internal balance coils. Note*** Olympus web information for this product is incorrect. The Nortec 2000D and Nortec 2000D+ do not h | 1 | |
| ACN16-MD6 | 16 Pin to Microdot NPID-1024 cable with No balance coil. Used with N500 series and N600 series instruments with internal balance coils. Note*** Olympus web information for this product is incorrect. The Nortec 2000D and Nortec 2000D+ do not have int... | 1 | |
| AF-5254 | Custom Nortec / Pratt & Whittney Eddy Current Probe, 2MHz, Dual "D'" Coil, .2.50mm, 5.6 UH Matching Inductance, Spring Loaded Tip, Differential / Bridge, Match phase angle and frequency as close as possible. Supplied with a Triax Fischer connector. | 1 | |
| DB3703-30 | MIDDLE REDUCTION AND TAIL REDUCTION OIL PIPES | 1 | |
| FC-2000 | BB Products FC-2000 Oil Filter Can Cutter | 1 | |
| FH-2000 | BB Products FH-2000 Oil Filter Holder | 1 | |
| IAE1R18928 | WRENCH, DUCT - AIR COOLED OIL COOLER INLET DUCT | 3 | |
| INIMD-700AK | MINI DUCTOR II KIT W/COIL SET | 1 | |
| LTCT3094-01 | Heater Assembly, Coil Induction | 1 | |
| P60361 | COVER-SHIPPING, ENGINE AIR OIL HEAT EXCH EXIT DUCT | 1 | |
| PRE65B00726 | Plug-side cowl oil breather duct | 1 | |
| PWA80214 | PULLER JACKSCREW ANGLE GEARBOX RADIAL DRIVE OIL DUCT | 1 | |
| PWA80278 | DRIFT ANGLE GEARBOX RADIAL DRIVE OIL DUCT INSTALLATION | 1 | |
| PWA81055 | ADAPTER TORQUE OIL DUCT RETAINING NUT | 1 | |
| PWA81311 | FIXTURE - HOLDING, LOWER TOWERSHAFT AND OIL DUCT - PW2000 ENGINES | 1 | |
| PWC71798 | COIL-INDUCTION HEAT | 1 |
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
