| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| 186-27MM | Eddy current standard | 1 | |
| 186-40MM | Eddy current standard | 1 | |
| 386B | Eddy current standard | 1 | |
| 389C | Eddy current standard | 1 | |
| BHCB-AL | EDDY CURRENT STANDARD | 1 | |
| BHCB-AL1 | EDDY CURRENT STANDARD | 1 | |
| ED-TB-AL | EDDY CURRENT STANDARD | 1 | |
| ED-TB-CS | EDDY CURRENT STANDARD | 1 | |
| ED-TB-TI | EDDY CURRENT STANDARD | 1 | |
| NDT-1041 | Eddy current standard | 2 | |
| NDT-1042 | Eddy current standard | 2 | |
| NDT-1043 | Eddy current standard | 2 | |
| NEC-6037 | Eddy current standard | 1 |
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| 10RS.47 | MD-11 Eddy current reference standard Section 2-1 Page 1 Figure 1.21 | 1 | |
| 132351 | EDDY CURRENT REFERENCE STANDARD | 1 | |
| 145-44131-001 | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, ALUMINUM ALLOY | 6 | |
| 145-44131-003 | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, STEEL ALLOY | 3 | |
| 145-44131-005 | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, TITANIUM ALLOY | 3 | |
| 145T09065-401 | REFERENCE STANDARD NDI (STAINLESS STEEL) -EDDY CURRENT TESTING | 1 | |
| 7374 | EDDY CURRENT BOLT HOLE STANDARD BLOCK (7075-T6 ALUMINUM) | 1 | |
| 235502 | CASA CN-235 EDDY CURRENT REFERENCE STANDARD PART 5 57-10-05 PAGE 510 FIGURE 504b. MATERIAL: 2024-T3 ALUMINUM. Includes Test Report and Certificate of Conformance. | 2 | |
| 1902510 | EDDY CURRENT CALIBRATION STANDARD ALUMINUM | 1 | |
| 208 FRONT SPAR | CESSNA / TEXTRON AVIATION EDDY CURRENT REFERENCE STANDARD 208 FRONT SPAR LOWER CAP. Drawing NO. 2683201 | 1 | |
| 208 REAR SPAR | CESSNA / TEXTRON AVIATION EDDY CURRENT REFERENCE STANDARD 208 REAR SPAR LOWER CAP. Drawing NO. 2683202 | 1 | |
| 2870020-001 | EDDY CURRENT STANDARD, WINGLET | 2 | |
| 3320A96900-301 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .004" W ± .001"), . MATERIAL 7075-T6 ALUMINUM. SIZE: 1.5"W x 3.00"L x .25" ± .005". Includes Test Report and Certificate of Conformance. | 1 | |
| 3320A96900-303 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .004" W ± .001"), . MATERIAL 7050-T7451 ALUMINUM. SIZE: 1.5"W x 3.00"L x .25" ± .005". Includes Test Report and Certificate of Conformance. | 1 | |
| 3320A96900-305 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .004" W ± .001"), . MATERIAL 15-5PH Steel. SIZE: 1.5"W x 3.00"L x .25" ± .005". Includes Test Report and Certificate of Conformance. | 1 | |
| 3320A96900-307 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .004" W ± .001"), . MATERIAL 6Al-4v Titaniuml. SIZE: 1.5"W x 3.00"L x .25" ± .005". Includes Test Report and Certificate of Conformance. | 1 | |
| 3765A96919-301 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. DHC-8-Q400 FOR INSPECTION OF OUTSIDE FUSELAGE CTS. ALL ALUMINUM PARTS ALODINED. Includes Test Report and Certificate of Conformance. | 1 | |
| 3765A96919-303 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. DHC-8-Q400 FOR INSPECTION OF OUTSIDE FUSELAGE CTS. ALL ALUMINUM PARTS ALODINED. Includes Test Report and Certificate of Conformance. | 1 | |
| 3765A96919-305 | CONAIR EDDY CURRENT SURFACE REFERENECE STANDARD. DHC-8-Q400 FOR INSPECTION OF OUTSIDE FUSELAGE CTS. ALL ALUMINUM PARTS ALODINED. Includes Test Report and Certificate of Conformance. | 1 | |
| 57-12-501 | RIGHT AND LEFT WING REAR BEAM AT BL 35.8 — EDDY CURRENT INSPECTION CALIBRATION STANDARD, 1159W40007-1NDT (GULFSTREAM) | 1 | |
| 57-12-502 | RIGHT AND LEFT WING REAR BEAM AT RBS 103.3 — EDDY CURRENT INSPECTION PROBE :SPO 5053 PROBE :SPO 5054 CALIBRATION STANDARD, 1159W40005-1NDT (GULFSTREAM | 1 | |
| 57-12-504 | RIGHT AND LEFT WING REAR BEAM AT RBS 230.1 — EDDY CURRENT INSPECTION CALIBRATION STANDARD, 1159W40063-1NDT (GULFSTREAM | 1 | |
| 6270-R1 | EDDY CURRENT REFERENCE STANDARD | 1 | |
| 6270-R2 | EDDY CURRENT REFERENCE STANDARD | 1 | |
| 6AL-6V-2SN-Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" +/-.001 DEEP, (MAX WIDTH .005"), 6AL-6V-2SNTi | 1 | |
| 7075-T6 | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, ALUMINUM ALLOY | 1 | |
| 7637987-9 | Eddy Current Inspection Reference standard | 1 | |
| 7947479-10 | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 3 | |
| 7947479-10 I | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 1 | |
| 7947479-10 S | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 1 | |
| 7947479-10 Ti | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 1 | |
| 7947479-10/17-4PH | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 1 | |
| 7947479-10/304SS | Air Force General Purpose Eddy Current Standard. Standard is a three (3) plate assembly measuring 4" x 7" x 1.06". Contains twenty (20) fastener holes with diameters from 0.156 to 0.750", two (2) screw holes, and two (2) dowel pins holes. Standard also co | 1 | |
| 98S55305011000 | EDDY CURRENT REFERENCE STANDARD | 2 | |
| A27288 | Eddy Current Inspection Reference standard SB DC9-27A235 R03 | 3 | |
| AFK-1017 | Custom Eddy Current Inspection Kit. Includes the following probes, Reference Standard and cables.AUR-.125SE/1.75WL-LF, AUR-.156SE/1.75WL-LF, AUR-.187SE/1.75WL-LF, AUR-.250SE/2.0WL-LF, AUR-.312SE/2.0WL-LF, AUR-.375SE/2.0WL-LF, AUR-.437SE/2.0WL-LF, AUR-... | 1 | |
| AFK-EC-BH16 | Boeing Part 6 51-00-00 Proceedure 16 Eddy Current Bolt Hole Inspection Kit. Includes 15 Universal Rotating Split End scanner probes Supplied with a with a Universal 4 Pin Fischer Connector and 1 Calibration Standard with hole sizes ranging from .187"Ø to | 1 | |
| AFK-ECS6 | EDDY CURRENT SURFACE PROBE KIT. Includes the Following Cable, Surface standards and probes: ACN16-TF6-B, AFNDT-2030/4340, AFNDT-2030/7075-T6, ATPN-45-5, ATPN-45-5FX, ATPN-5, ATPN-5FX, ATPN-95-5, ATPN-95-5, PELICAN STYLE WATERPROOF kIT BOX. Supplied wit... | 1 | |
| AFNDT-0512A | Eddy Current Hole and Surface Crack Standard: 7075-T651 Aluminum.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-0512A. | Eddy Current Surface Crack Standard. EDM Notch Size: Total of 3 Notches, 0.005, 0.010, 0.020 Deep x .005W +/- .002 per 33B-1-2 WP 402 00. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-0512T | Eddy Current Hole and Surface Crack Standard: 6AL-4v Titanium.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1017AL | Custom Eddy Current Hole Standard 7075-T7 Aluminum ( Equivalent substitute for 7010 Aluminum). Hole Sizes 1.77" and 0.58" diameter. EDM flaw size: 0.5mm(.020") x 0.1mm (0.004") +/- .002". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-1080/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES 0.5mm, 1.0mm, 2.0mm, 3.00mm, 4.0mm, 5.0mm (.004"W +/- .002, MAX.006), 4340 STEEL 1.0"W x 7.0"L. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2004 | EDDY CURRENT SURFACE STANDARD WITH 3 EDM NOTCHES: ( .005", .010", .020" Deep x .004"Wide +/- .002 ), MATERIAL: 7075-T6 ALUMINUM. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/13-8 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/13-8PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 13-8PH MO STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/17-7PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 17-7PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2014-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2014-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T3 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/2024-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.004W +/- .002), MATERIAL: 2024-T6 ALUMINUM. SIZE: 4.0"L x 1.0"W x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/300M | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: 300M STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/301 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), CRES 301 1/2 HARD(MIL-S-5059) 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/304L | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 304L STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/316SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 316 STAINLESS STEEL 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4130 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4130 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/6061-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002), 6061-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-2030/7075-T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/7075-T7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/718 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 718 INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/I600 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), 600 SERIES INCONNEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/MAR | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .002). MATERIAL: 250 MARAGING STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/N200 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002), MATERIAL: NICKEL 200. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2030/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX .006"), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and COC | 1 | |
| AFNDT-2030CS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008", .020", .040" (.004"W +/- .002, MAX.006), 4130 or 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/6AL4V | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2107/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM FLAWS: .008", .020", .040" (.005" Maximum Width). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25"H. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2114AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.006W +/- .001). BLOCK SIZE:3.156 "L x 1.375"W x .312"H. MATERIAL: 2024-T3 ALUMINUM.. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-2151AL | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCHES .008", .020", .040" (.005"W + .001"), MATERIAL: 5086 H32 ALUMINUM. (29.0% IACS. SIZE: 80mm(3.15") L +5mm(.197") x 30mm(1.18") W +5mm(.197") x 8mm(.315") THICK +3mm(.118"). Includes Mill Certifica... | 1 | |
| AFNDT-2227Ti | CUSTOM TITANIUM EDDY CURRENT MULTI HOLE STANDARD WHICH COMBINES BOEING PART NUMBERS NDT1022-NDT1027 STANDARDS INTO ONE PART..HOLE SIZES ( 0.188", 0.250", 0.313", 0.375",0.438", 0.500" ). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3015 | EMBRAER 170/190 SERIES EDDY CURRENT SURFACE REFERENCE STANDARD 50-00-00 PT 1 PAGE 4, Aluminum(7075-T6) 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3019S | CUSTOM AIR FORCE EDDY CURRENT BOLT HOLE STANDARD PER CUSTOMER SUPPLIED DRAWING, 1/4" 8630 STEEL PLATE (4130 EQUIVALENT ALTERNATIVE). EDM: 0.030 x 0.030 CORNER NOTCH. HOLE DIAMETER= 0.437Ø. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3025AL | Eddy Current Surface Standard 7075-T6 Aluminum. Block Size: 4.0"(101.6mm)L x 1.0"(25.4mm)W x .25"(6.35mm)H. Includes 3 EDM Flaws of the following sizes...1.) (0.5mm)D x (0.25mm)W x (25mm)L..2.) (1.0mm)D x (0.25mm)W x (25mm)L..3.) (2.0mm)D x (0.25mm)W x... | 1 | |
| AFNDT-3025CS | Eddy Current Surface Standard 4340 Carbon Steel. Block Size: 4.0"(101.6mm)L x 1.0"(25.4mm)W x .25"(6.35mm)H. Includes 3 EDM Flaws of the following sizes...1.) (0.5mm)D x (0.25mm)W x (25mm)L..2.) (1.0mm)D x (0.25mm)W x (25mm)L..3.) (2.0mm)D x (0.25mm)W ... | 1 | |
| AFNDT-3025INC | Eddy Current Surface Standard 718 Inconel. Block Size: 4.0"(101.6mm)L x 1.0"(25.4mm)W x .25"(6.35mm)H. Includes 3 EDM Flaws of the following sizes...1.) (0.5mm)D x (0.25mm)W x (25mm)L..2.) (1.0mm)D x (0.25mm)W x (25mm)L..3.) (2.0mm)D x (0.25mm)W x (25m... | 1 | |
| AFNDT-3025SS | Eddy Current Surface Standard 304 Stainless Steel. Block Size: 4.0"(101.6mm)L x 1.0"(25.4mm)W x .25"(6.35mm)H. Includes 3 EDM Flaws of the following sizes...1.) (0.5mm)D x (0.25mm)W x (25mm)L..2.) (1.0mm)D x (0.25mm)W x (25mm)L..3.) (2.0mm)D x (0.25mm)... | 1 | |
| AFNDT-3025TI | Eddy Current Surface Standard 6AL-4V Titanium. Block Size: 4.0"(101.6mm)L x 1.0"(25.4mm)W x .25"(6.35mm)H. Includes 3 EDM Flaws of the following sizes...1.) (0.5mm)D x (0.25mm)W x (25mm)L..2.) (1.0mm)D x (0.25mm)W x (25mm)L..3.) (2.0mm)D x (0.25mm)W x ... | 1 | |
| AFNDT-3026AL | EDDY CURRENT SURFACE REFERENCE STANDARD Leonardo Helicopters SB No. 109EP-158. MATERIAL: 7475-T7 ALUMINUM. SIZE: 1.0" x 3.0" x .25" EDM SLOT (0.5mm DEEP) x (0.05-0.25mm WIDE) +/-.03mm. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3035SS | EDDY CURRENT SURFACE REFERENCE STANDARD. EDM NOTCHES: .005", .010", .020", .060" (.005"W +/- .002, MAX.007" WIDE). MATERIAL: 301 1/2 HARD STAINLESS STEEL(MIL-S-5059) 1.0"W x 4.0"L x .125", NOTE: .750" DISTANCE BETWEEN EACH NOTCH. Includes Test Repor... | 1 | |
| AFNDT-3036AL | CUSTOM 2 HOLE EDDY CURRENT REFERENCE STANDARD. MATERIAL: 7075-T6 ALUMINUM. HOLE SIZES: .250" and .875" WITH a .030" x .030" x .007" MAX WIDTH CORNER EDM NOTCH IN EACH HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3037 | CUSTOM EDDY CURRENT HOLE REFERENCE STANDARD. MATERIAL: 718 INCONEL. HOLE SIZE: .256"Ø WITH a 0.1" x 0..1" x .010" +/- .002" EDM NOTCH IN THE BOTTOM RADIUS OF THE HOLE. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3055 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4330 STE... | 1 | |
| AFNDT-3058/INC | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .5mm, 1.0mm, 2.0mm x (.006"Wide +/- .001). MATERIAL: 718 Inconel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3058SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES: 0.5mm, 1.0mm, 2.0mm x (.005"Wide + .000/-.002). MATERIAL: 304 Stainless Steel. SIZE: 1.0" Wide x 4.0" Long x 0.25" Thick. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3059 | Custom Eddy Current 2 Hole Calibration Standard per Customer Supplied Drawing. Material: 7050-T7451. Hole Sizes: .516"Ø and .812"Ø with a total of 4 EDM Notches 0.021" x 0.021" x .004" Wide Max. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3060 | Custom Eddy Current 2 Hole Calibration Standard per Customer Supplied Drawing. Material: 7050-T7451. Hole Sizes: .252"Ø and .516"Ø with a total of 4 EDM Notches 0.021" x 0.021" x .004" Wide Max. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3061AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020" (.004"W +/- .002), 7075-T7 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3071 | Custom designed eddy current multi-layer aircraft aluminum skin test specimen, drawing 2, sheets 1-4. reference standard for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3072 | Custom designed eddy current aircraft calibration standard, Drawing 3, Sheets 1-3, for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3073 TYPE 1 | Custom designed eddy current reference standard for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3073 TYPE 2 | Custom designed eddy current reference standard for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3073 TYPE 3 | Custom designed eddy current reference standard for Central Piedmont Community College. Material: 2024-T3 Aluminum. Includes Certification Report Traceable to NIST. | 1 | |
| AFNDT-3154CS | Eddy Current Surface Standard Carbon Steel. 0.5mm, 1.0mm,2.0mm Deep x .15mm Wide +/- .05mm. Block Size: 5.0"(127mm)L x 2.0"(50.8mm)W x .25"(6.35mm). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3154SS | Eddy Current Surface Standard 316 Steel. 0.5mm, 1.0mm,2.0mm Deep x .15mm Wide +/- .05mm. Block Size: 5.0"(127mm)L x 2.0"(50.8mm)W x .25"(6.35mm). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3160AL | BOMBARDIER EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .005" W +0.00, - .002"), DEPTH TOLERANCE = +/- .001"(+/- .003mm). MATERIAL 2024-T3 ALUMINUM. SIZE: 1.5"W x 3.75"L x .25". Includes Test Report and Certificate of... | 1 | |
| AFNDT-3160AL-1 | BOMBARDIER EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .005" W +0.00, - .002"), DEPTH TOLERANCE = +/- .001"(+/- .003mm). MATERIAL 6061-T6 ALUMINUM, IACS 40.00-44.80. SIZE: 1.5"W x 3.75"L x .25". Includes Test Report and | 1 | |
| AFNDT-3160AL-2 | BOMBARDIER EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .005" W +0.00, - .002"), DEPTH TOLERANCE = +/- .001"(+/- .003mm). MATERIAL 2024-T6 ALUMINUM, SIZE: 1.5"W x 3.75"L x .25". Includes Test Report and Certificate of ... | 1 | |
| AFNDT-3160CS | BOMBARDIER EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .005" W +0.00, - .002"), DEPTH TOLERANCE = +/- .001"(+/- .003mm). MATERIAL 4130/4340 CRES STEEL. SIZE: 1.5"W x 3.75"L x .25". Includes Test Report and Certificat... | 1 | |
| AFNDT-3160SS | BOMBARDIER EDDY CURRENT SURFACE REFERENECE STANDARD. EDM Notches: .008", .020", .040" ( .005" W +0.00, - .002"), DEPTH TOLERANCE = +/- .001"(+/- .003mm). MATERIAL: 304 STAINLESS STEEL. SIZE: 1.5"W x 3.75"L x .25". Includes Test Report and Certificat... | 1 | |
| AFNDT-3201/321SS | EDDY CURRENT SURFACE REFERENCE STANDARD, 321SS 3 EDM SLOTS (0.2mm, 0.5mm,1.0mm DEEP) x (0.05-0.25mm WIDE). Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3224TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005", .010", .020", .040", .060" (.005"W +/- .002, MAX .007"). MATERIAL: 6AL-4v TITANIUM@2.2IACS. SIZE: 1.0"W x 6.0"L x .500". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3231 | Custom McDonnell Douglas Low Frequency Eddy Current reference standard, 06-20-01 Figure 9 sheets 1-4. Material: 2024-T3 or 7075-T6 Aluminum. Fasteners: (NAS1097AD6-5 & BACB30NW6K3). Includes Test Report and Certificate of Confromance. | 1 | |
| AFNDT-3231-1 | Custom McDonnell Douglas Low Frequency Eddy Current reference standard, 06-20-01 Figure 9 sheets 1-4. Material: 2024-T3 or 7075-T6 Aluminum.Fasteners: (CR3223-5 & MS21141-5). Includes Test Report and Certificate of Confromance. | 1 | |
| AFNDT-3233F | Custom Eddy Current Surface Standard. Size: 80mm x 35mm x 7mm. Material: Forged Aluminum. EDM Notch: .060" Long x .004" Wide x .030" Deep +/- 0.002". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3279/15-5PH | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 15-5PH STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3279/Ti | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010", .020", .050" .007" ,MAX WIDTH, 6AL-4V TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3284SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm), .050"(1.27mm) (.004"W +/- .001), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. REFERENCE P/N:29A049 | 1 | |
| AFNDT-3285/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-4PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/17-7 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: 17-7PH Steel Condition to TH1050. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3285/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .005"(0.127mm), .010"(0.254mm), .020"(0.508mm) (.004"W +/- .002). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, METRIC NOTCHE SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3306/MAG | EDDY CURRENT METRIC SURFACE REFERENCE STANDARD. EDM NOTCH SIZES: 0.2mm, 0.5mm &1.0mm. WIDTH = .005" +/- .002" MATERIAL: MAGNESIUM ZK60A-T5 PER ASTM-B107. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3308AL | Eddy Current Calibration Standard 3/8” diameter hole standard. Material: 2024-T3 standard with a .030”x .030" corner notch. Includes Certification Report traceable to NIST. | 1 | |
| AFNDT-3315AL | EDDY CURRENT SURFACE REFERENCE STANDARD, 4 EDM NOTCHES .005", .010", .020" and .050" x (.004"W +/- .002). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3319SS | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .020"(0.5mm), .040"(1.0mm), .079"(2.0mm) (.005"W +/- .002), 304 STAINLESS STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3347CS | EDDY CURRENT WELD SURFACE REFERENCE STANDARD. EDM NOTCHES: 0.5mm, 1.0mm, 2.0mm (.1mm (.004") WIDE ± .05mm( .002") MAX WIDTH .152mm (.006"). MATERIAL: 4340 CARBON STEEL. SIZE: 1.0"W x 4.0"L Includeds 4 piece .020" thick shim and Key Ring set. Includes Tes | 1 | |
| AFNDT-3357/2024T4 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .008"(0.2mm), .020"(0.5mm), .040"(1.0mm) (.004"W +/- .001), 2024-T4 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance and Material Certification. | 1 | |
| AFNDT-3370/4340 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 4340 STEEL. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/7075T6 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(0.76mm) (.004"W +/- .002), 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3370/TI | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.25mm), .020"(0.5mm), .030"(.76mm) (.004"W +/- .002), 6AL-4v TITANIUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3412 | Custom Eddy Current Surface Standard with a Total of 12 EDM Notches. Notch Lenghs of .125, .250", .375" and .625". Notch Depths of .008", .020", and .040" for each length. Material: Nickel Aluminum Bronze. Includes Test Report and Certificate of Conforman | 1 | |
| AFNDT-3413 | Custom Boeing Eddy Current Hole Standard. Hole Sizes: .159 & .190"Ø. With one of each hole size plugged. Material: 2024-T3 Aluminum. Plugged holes contain a BACR15BA6A8C Rivet in the .056" plate. Apply BMS 545 sealant between each layer Includes Test Repo | 1 | |
| AFNDT-3423 | Eddy Current Reference Standard. Dimensions: 4" x 0.25" x 1" Material: Aluminum 7075-T7. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3425 | Custom Eddy Current Multi-Hole Reference Standard. Hole Diameters: 7.0 mm, 7.5 mm, 8.0 mm, 8.5 mm, 9.0 mm, 9.5 mm, 10.0 mm, 10.5mm, 11.0 mm, 11.5 mm, 12.0 mm, 12.5 mm, 13.0 mm, 13.5 mm, 14.0 mm. Two (2) EDM notches per hole.Material: Aluminium 7075-T76. | 1 | |
| AFNDT-3426 | Custom Eddy Current Hole Standard. Hole Diameters: 4.0 mm, 4.5 mm, 5.0 mm, 5.5 mm, 6.0 mm, 6.5 mm, 7.0 mm, 7.5 mm, 8.0 mm, 8.5 mm, 9.0 mm, 9.5 mm, 10.0 mm, 10.5 mm, 11.0 mm, 11.5 mm, 12.0 mm. Material: Aluminium 7050-T74. Includes Test Report and Certific | 1 | |
| AFNDT-3439/6AL-4V | EDDY CURRENT SUIRFACE STANDARD WITH A TOTAL OF THREE A3 TYPE SURFACE NOTCHES ORIENTATED AT 0°, 45° and 90°. MATERIAL: 6AL-4V TITANIUM. SIZE: 2.0" Wide X 4.0" Wide. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3439/718 | EDDY CURRENT SUIRFACE STANDARD WITH A TOTAL OF THREE A3 TYPE SURFACE NOTCHES ORIENTATED AT 0°, 45° and 90°. MATERIAL: 718 INCONEL SIZE: 2.0" Wide X 4.0" Wide. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3440/304 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: Non-Magnetic 304 Stainless Steel. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3440/6AL-4V | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.508mm), .050" (1.27mm) (.004"W +/- .001). Material: 6AL-4V Titanium. SIZE: 1.0"W x 3.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3457 | EDDY CURRENT SURFACE REFERENCE STANDARD. Cadmium plated on one side to AMS-QQ-P-416-f Type 1, Class 2. 3 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .008", .020", .040". NOTCH WIDTH: (.004"W +/- .002). MATERIAL: 4340 STEEL. SIZE: 1. | 1 | |
| AFNDT-3459AL | Calibration standard, Aluminium alloy 2024-T3, rotary (dynamic) eddy current testing, cross-drilled hole type per BAe 146 Ref. NTM Part 6,20-00-00), for diameters of (5/16 in. (7.94 mm), 13/16 in. (20.64 mm), 7/8 in. (22.23 mm), 1.1/16 in. (26.99 mm), 1. | 1 | |
| AFNDT-3459TI | Calibration standard, 6Al-4v Titanium , rotary (dynamic) eddy current testing, cross-drilled hole type per BAe 146 Ref. NTM Part 6,20-00-00), for diameters of (5/16 in. (7.94 mm), 13/16 in. (20.64 mm), 7/8 in. (22.23 mm), 1.1/16 in. (26.99 mm), 1.1/8 in | 1 | |
| AFNDT-3460AL | Custom Eddy Current Bolt Hole Calibration Standard. Total of 35 Hole Sizes: Diameters 3.0mm, 3.2mm, 4.0mm, 4.2mm, 4.6mm, 5.0mm, 5.4mm, 5.8mm, 6.2mm, 6.6mm, 7.0mm, 7.4mm, 7.8mm, 8.0mm, 8.2mm, 8.6mm, 9.0mm, 9.4mm, 9.8mm, 10.2mm, 10.6mm, 11.0mm, 11.4mm, 11. | 1 | |
| AFNDT-3470/17-4 | EDDY CURRENT SURFACE REFERENCE STANDARD, EDM NOTCH .020"(0.5mm), (.004"W +/- .002), 17-4PH STEEL. SIZE: 1.0"W x 3.0"L x .25".Includes certification Report Traceable to NIST and Certificate of Conformance(COC). | 1 | |
| AFNDT-3471AL | Custom Eddy Current Bolt Hole Calibration Standard Manufactured in Accordance with Airbus Specification 51-63-04. Total of 14 Hole Sizes x 4 For a Total of 56 Holes: Diameters 13.5mm(.531"), 14.1mm(.555"), 14.3mm(.563"), 15.0mm(.591"), 15.8mm(.622"), ... | 1 | |
| AFNDT-3472AL | Custom Eddy Current Bolt Hole Calibration Standard Manufactured in Accordance with Boeing Specification 51-00-00. Total of 14 with 28 EDM Notches. Hole Sizes: Diameters 13.5mm(.531"), 14.1mm(.555"), 14.3mm(.563"), 15.0mm(.591"), 15.9mm(.625"), 16.7mm(... | 1 | |
| AFNDT-3484AL | Eddy Current Bolt Hole Calibration standard, 5 Hole Sizes. Material: 7075-T6 Aluminium, Hole diameters: .750", .875",1.00" 1.125" 1.187", .030" x .030" x .005" ± .001" Corner EDM Notch in each hole. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3485AL | Eddy Current Bolt Hole Calibration standard, 3 Hole Sizes. Material: 7075-T6 Aluminium, Hole diameters: 1.250" 1.375", 1.500", .030" x .030" x .005" ± .001" Corner EDM Notch in each hole. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3499 | EDDY CURRENT SURFACE REFERENCE STANDARD. Low Hydrogen Embrittlement Cadmium-Titaniium Alloy Plating per BAC5804. 4 EDM FLAWS ON BOTH SIDES. ONE SIDE UNPLATED(BARE). NOTCH DEPTHS : .005", .010", .020", .050". NOTCH WIDTH: (.007" +/- .002"). MATERIAL: 4... | 1 | |
| AFNDT-3512AL | MISTRAS 3 HOLE EDDY CURRENT TEST STANDARD, HOLE SIZES: .250", .375", .500" DIAMETERS, EDM CORNER NOTCH: .025" x .025" x .005 ± .002", MID-WALL NOTCH:.080" x .025" DEEP +/-.002" per BSS7048. 1 SURFACE EDM NOTCH .150" LONG x .030" DEEP. ALL NOTCHES TO B... | 1 | |
| AFNDT-3522AL | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 7075-T6 ALUMINUM. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522SS | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 304 STAINLESS STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3522ST | CUSTOM EDDY CURRENT SURFACE REFERENCE STANDARD, 3 EDM SLOTS .008",.020",.040" .006" ±.001". MATERIAL: 4340 STEEL. SIZE: .312" THICK x 1.375 WIDE x 3.156". Includes Test Report and Certifictate of Conformance. | 1 | |
| AFNDT-3534/2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHES .010"(0.254mm), .020"(0.5mm), .030"(.762mm) (.004"W +/- .002), 2024-T3 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3541AL | EDDY CURRENT SURFACE STANDARD MANUFACTURED TO BSS 7698,..3 EDM NOTCHES: ( .010", .020", .030" Deep x .005" Wide ± .001 ), MATERIAL: 7075-T6 Aluminum. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3541ST | EDDY CURRENT SURFACE STANDARD MANUFACTURED TO BSS 7698,.. 3 EDM NOTCHES: ( .010", .020", .030" Deep x .005" Wide ± .001 ), MATERIAL: 4340 Steel. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3541TI | EDDY CURRENT SURFACE STANDARD MANUFACTURED TO BSS 7698, ..3 EDM NOTCHES: ( .010", .020", .030" Deep x .005" Wide ± .001 ), MATERIAL: 6AL-4V Titanium. Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-3546AL | EDDY CURRENT SURFACE REFERENCE STANDARD, NOTCHE SIZES: .005"(.127mm) , .020"(0.5mm), .050"(1.27mm) (.005"W +/- .001). MATERIAL: 7075-T6 ALUMINUM. SIZE: 1.0"W x 4.0"L x .25". Includes Test Report and Certificate of Conformance. | 1 | |
| AFNDT-ECRC82040 | Eddy Current Crack Standard Magnesium AZ-31 | 1 | |
| AGE-02001-401 | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, ALUMINUM ALLOY | 1 | |
| AGE-04383-001 | STANDARDS SET - REFERENCE, NDI – GENERAL EDDY CURRENT TEST | 1 | |
| AGE-04707-401 | SET - REFERENCE STANDARD NDI - GENERALEDDY CURRENT TEST | 2 | |
| AGE-04900-401 | EDDY CURRENT INSTRUMENT - IMPEDANCEPLANE DISPLAY OR SIMILAR REFERENCE STANDARD, NDI, ALUMINUM7050-T7451 | 4 | |
| ANDT1015 | EDDY CURRENT REFERENCE STANDARD | 3 | |
| ARS-123/TI | EDDY CURRENT SURFACE REFERENCE STANDARD. MATERIAL: TI-6AL-6V-2SN. SIZE: 2.0" LONG x 1.0" WIDE. EDM NOTCH .040" DEEP +/- .002" x .005" WIDE +/- .001". Includes Test Report and Certificate of Conformance. | 1 | |
| COUPON 12 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-3. 05-30-10 PG.193. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 2 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-4. 05-30-10 PG.190. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 25 | PEMCO LOW FREQUENCY EDDY CURRENT STANDARD FOR INSPECTION UJ-1. 05-30-10 PAGE 194. EDM NOTCH: .030 MAX WIDTH x .240" LONG. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 29 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-3 and ED-4. 05-30-10 PG.195. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 3 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-3. 05-30-10 PG.191. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 31 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-5. 05-30-10 PG.196. Includes Certification Report Tracable to NIST. | 1 | |
| COUPON 6 | PEMCO WORLD AIR SERVICES EDDY CURRENT LOW FREQUENCY STANDARD. COUPON FOR USE WITH INSPECTION ED-5. 05-30-10 PG.192. Includes Certification Report Tracable to NIST. | 1 | |
| DAC ETOH-AL-1/2 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 1/2 (0.500) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-1/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 1/4 (0.250) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-1/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 1/8 (0.125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-11/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 11/16 (0.6875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-3/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 3/16 (0.1875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-3/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 3/4 (0.750) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-3/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 3/8 (0.375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-5/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 5/16 (0.3125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-5/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 5/8 (0.625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-7/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 7/16 (0.4375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-AL-9/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Aluminum. 9/16 (0.5625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-1/2 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 1/2 (0.500) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-1/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 1/4 (0.250) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-1/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 1/8 (0.125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-11/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 11/16 (0.6875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-3/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 3/16 (0.1875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-3/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 3/4 (0.750) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-3/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 3/8 (0.375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-5/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 5/16 (0.3125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-5/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 5/8 (0.625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-7/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 7/16 (0.4375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-FE-9/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Steel. 9/16 (0.5625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-1/2 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 1/2 (0.500) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-1/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 1/4 (0.250) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-1/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 1/8 (0.125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-11/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 11/16 (0.6875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-3/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 3/16 (0.1875) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-3/4 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 3/4 (0.750) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-3/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 3/8 (0.375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-5/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 5/16 (0.3125) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-5/8 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 5/8 (0.625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-7/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 7/16 (0.4375) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| DAC ETOH-IT-9/16 | McDonnell Douglas Open Hole Eddy Current Reference Standard Part 6 06-20-01 Page F10 Figure 4. Material: Titanium. 9/16 (0.5625) Inch Hole. Includes Test Report and Certificate of Conformance. | 1 | |
| EC-AF-NRK-Case | CASE FOR EDDY CURRENT STANDARD TOOL | 1 | |
| ETD2015-145-108529 | CUSTOM EDDY CURRENT STANDARD, 2024-T351 ALUMINUM .063"/.050". MS20426AD5 CSK RIVET 2 PLACES | 1 | |
| G601R572101-1 | CALIBRATION STANDARD - EDDY CURRENT INSPECTION (4777 CYCLES) | 1 | |
| G601R572101−1 | Calibration Standard − Eddy Current Inspection (4777 cycles) | 1 | |
| GSE 539 | GSE 539 STANDARDS SET - REFERENCE, NDI - GENERAL EDDY CURRENT TES | 1 | |
| Honeywell ET Standard | Honeywell Eddy Current Wheel Surface Standard. Material:2024-T6 Forged Aluminum. Includes Test Report and Certificate of Conformance. | 1 | |
| NDT 7014 | EDDYCURRENT CALIBRATION STANDARD | 2 | |
| NDT 745 | EDDYCURRENT CALIBRATION STANDARD | 2 | |
| NDT 786A | EDDYCURRENT CALIBRATION STANDARD | 2 | |
| NDT-3014B | Eddy current standard set | 1 | |
| NDT1084-0,125 | EDDY CURRENT REFERENCE STANDARD | 1 | |
| NDT1084-0,156 | EDDY CURRENT REFERENCE STANDARD | 2 | |
| NDT520 | Eddy Current Inspection Reference standard 757 | 1 | |
| NRK-CASE | CASE FOR EDDY CURRENT STANDARD TOOL | 1 | |
| PWA28403 | CRACK STANDARD-EDDY CURRENT 1ST STAGE FAN BLADE | 4 | |
| PWA84306 | EDDY CURRENT STANDARD & CAL CARD | 1 | |
| PWA84314 | REFERENCE STANDARD FOR EDDY CURRENT TEST ON PW2000 SERIES ENGINE FAN BLADES | 1 | |
| PWC45291 | EDDY CURRENT CALIBRATION STANDARD | 1 | |
| RM120-C30-304-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 304 STAINLESS STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RM120-C30-4340-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 4130 STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RM120-C30-7075T6-1 | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 7075-T6 ALUMINUM, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| RS0824-2024T3 | EDDY CURRENT SURFACE REFERENCE STANDARD | 1 | |
| SB09270209-5 | Eddy Current Inspection Reference standard SB DC9-27-209 R07 | 1 | |
| SB09530016-5 | Eddy Current Inspection Reference standard SB MD-A27-320 R01 | 2 | |
| SB09530186-9 | Eddy Current Inspection Reference standard SB DC9-53-186 R06 | 1 | |
| SE.4.44 | 328JET CALIBRATION STANDARD (SE.4.44); 51-60-01 PAGE 9/10 FIG.605 EDDY CURRENT | 1 | |
| SO111-7 | Custom FOKKER F28 Horizontal Stab. Drive Junction Fitting Eddy Current Standard per drawing # 28. 0-3210/2610-Material: 7075-T6. Includes Test Report and Certificate of Conformance. | 1 | |
| SRSM-2510T | REFERENCE STANDARD, GENERAL EDDY CURRENT TESTING, TITANIUM ALLOY | 1 | |
| SS137-F2 | NDT REFERENCE STANDARD EDDY CURRENT | 1 | |
| ST4130 | BOMBARDIER / CANADAIR EDDY CURRENT SURFACE REFERENCE STANDARD PART 6 55-20-001, NOTCHES .008", .020", .040" (.005" Wide +000 / - .002 and +/- .001" Depth), MATERIAL: 4130 STEEL. Includes certification Report and Certificate of Conformance(COC)... | 1 | |
| TB-16 | NORTEC EDDY CURRENT STANDARD | 1 | |
| TEK-9117 | CRACK STANDARD-EDDY CURRENT 1ST STAGE FAN BLADE | 1 | |
| VM30889-C1A | EDDY CURRENT GENERAL CALIBRATION STANDARD | 2 | |
| VM89A | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 7075-T6 ALUMINUM, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| VM89S | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 4130 STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| VM89SS | GENERAL PURPOSE EDDY CURRENT REFERENCE STANDARD, 304 STAINLESS STEEL, 12 HOLES 3/16” TO ¾” DIAMETERS, EACH HOLE CONTAINS A .030” X .030” CORNER EDM NOTCH, THREE SURFACE NOTCHES - .010”, .020” & .040” DEEP X ¾” LONG | 1 | |
| VMA3RS-1.0 | HF EDDY CURRENT REFERENCE STANDARD | 1 |
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
